background image

Montrose Woodfire

27

operating 

 instructions

WARNING:  To build a fire in igno

-

rance or to disregard the information 

contained in this section can cause 

serious permanent damage to the 

unit and void your warranty!!

AIR SLIDE CONTROL

Both the primary and air wash drafts are controlled 

by the control rod located at the bottom of the unit 

(when facing the unit).  To increase your draft - pull 

right to open, and to decrease - push left.  All units 

have a secondary draft system that continually al-

lows combustion air to the induction ports at the top 

of the firebox, just below the flue baffle.

OPERATING 

INSTRUCTIONS

With your unit now correctly installed and safety 

inspected by your local authority, you are now ready 

to start a fire.  Before establishing your first fire, it 

is important that you fully understand the operation 

of your draft control.

WARNING: ANY MODIFICATION OF THE AP-

PLIANCE THAT HAS NOT BEEN APPROVED 

IN WRITING BY THE TESTING AUTHORITY IS 

CONSIDERED AS BREACHING AS/NZS 4013.

WARNING: DO NOT USE FLAMMABLE LIQUIDS 

OR AEROSOLS TO START OR REKINDLE THE 

FIRE.

WARNING: DO NOT USE FLAMMABLE LIQUIDS 

OR AEROSOLS IN THE VICINITY OF THIS AP-

PLIANCE WHEN IT IS OPERATING.

WARNING: DO NOT STORE FUEL WITHIN 

HEATER INSTALLATION CLEARANCES.

CAUTION: THIS APPLIANCE MUST BE MAIN-

TAINED AND OPERATED AT ALL TIMES IN 

ACCORDANCE WITH THESE INSTRUCTIONS.

WARNING: OPEN AIR CONTROL (AND DAMPER 

WHEN FITTED) BEFORE OPENING FIRING 

DOOR.

CAUTION: THIS APPLIANCE SHOULD NOT BE 

OPERATED WITH A CRACKED GLASS.

CAUTION: THIS APPLIANCE SHOULD BE 

MAINTAINED AND OPERATED AT ALL TIMES IN 

ACCORDANCE WITH THESE INSTRUCTIONS. 

CAUTION:  THE  USE  OF  SOME  TYPES  OF 

PRESERVATIVE-TREATED  WOOD  AS  A  FUEL 

CAN BE HAZARDOUS.

For safety reasons and in order to avoid over 

firing of your unit do not burn your fire with 

the door open or ajar

WARNING:  Do not over-fire this unit and always open the door slowly when reloading

FUEL REQUIREMENTS

BURN ONLY HARDWOOD TIMBER THAT HAS 
BEEN SEASONED AND THE MOISTURE CON-
TENT OF THE LESS THAN 20%.

FRESHLY CUT WOOD REQUIRES AT LEAST 12-
18 MONTHS TO BE READY FOR USE. 

USING SEASONED TIMBER WITH PROPER 
MOISTURE CONTENT WILL ENSURE DRAFT, 
CLEAN GLASS, EFFICIENCY AND HEAT OUT-
PUTS.

CAUTION: BURN UNTREATED AIR DRIED SEA-
SONED HARDWOODS ONLY. OTHER MATERI-
ALS SUCH AS WOOD PRESERVATIVES, METAL 
FOILS, COAL, PLASTIC, GARBAGE, SULPHUR 
COAL, BRIQUETTES OR OIL WILL DAMAGE 
THE FIRE AND ATMOSPHERE AND VOID THE 
WARRANTY.

"This  wood  heater  is  designed  to  burn  natural 
wood only. Higher efficiencies and lower emissions 
generally result when burning air dried seasoned 
hardwoods,  as  compared  to  green  or  freshly  cut 
hardwoods."

DO NOT BURN 

(WILL VOID WARRANTY) 

 

• Treated wood

 

• Tea Tree

 

• Oil based woods

 

• Coal

 

• Garbage

 

• Cardboard

 

• Solvents

 

• Colored Paper

 

• Trash

   

SAVE THESE INSTRUCTIONS

WOOD STORAGE

Store wood under cover, such as in a shed, or 

covered with a tarp, plastic, tar paper, sheets 

of scrap plywood, etc., as uncovered wood can 

absorb water from rain or snow, delaying the 

seasoning process.

Содержание L850B

































Отзывы: