Regency Greenfire GF900C Скачать руководство пользователя страница 38

Страница: 38 / 68

Regency GF900C-2 Gas Fireplace

installation

920-039

04/23/19

Installer Notice:

These instructions must be left

with the appliance.

After carrying out all adjustments, block the setting screws with
paint, taking care not to obstruct the breather orifice of the pres-
sure.

Put back the modulator plastic cap.

WARNING:

To ensure the correct operation of the modulator it is

necessary that the plastic cap (A) is returned to its original loca-
tion.

18.

Turn on gas supply and plug in power cord.

19.

At the end of all setting and adjustment operations, check electri-

cal installation and gas leaks.

20.

Check operation of flame control.

21.

Check for proper flame appearance and glow on logs.

Reinstall new burner orifice Propane stamped #53 or ULPG
burner orifice stamped #53 and tighten.

. Replace the black "NATURAL GAS" label with the orange "PRO-

PANE" label or red for “UNIVERSAL LPG” label.

. Carefully pull out the control box.

NOTE

: The control box is held in place with velcro.

. Remove the heat shield from the control box by removing the 2

screws.

. Remove the control box cover by undoing the 3 screws.

Manoeuvre through antenna.

14.

Reverse steps 12-11.

15.

Adjust the air shutter opening (See page 37 for Aeration Adjust-

ment).

Reverse steps 4-2 and 1.

16.

Turn on gas supply and plug in power cord.

Cable

Electric
Modulator

Control Box

Cover

Antenna

Jumper Location

. Remove the jumper using pliers.

Jumper

17. Adjusting the Outlet Pressure

All the adjustments must be carried out in the following order:

Remove the modulator plastic cap (A) using needle nose pliers.

Maximum pressure:

Turn the unit ON to its highest input

rating. Screw in the nut (B) to increase the outlet pressure and
screw it out to decrease it. Use a 10 mm wrench.

NOTE:

The outlet pressure must be set to maximum 2.49 kPa.

Minimum pressure:

Remove one of the cables connected to the

electric modulator. While holding the nut (B) with a wrench, screw
in the screw (C) to increase the pressure and screw it out to
decrease it. Use a screwdriver 6 x 1 blade.

NOTE: The outlet pressure must be set to minimum 1.6

kPa.

GF900C-2

Содержание Greenfire GF900C





































































Результаты поиска

Содержание Greenfire GF900C

Отзывы:

Похожие инструкции для Greenfire GF900C

Бренды по названию

Популярные бренды

Regency Greenfire GF900C, Инструкция для владельца и по установке

Результаты поиска

Содержание Greenfire GF900C

Отзывы:

Похожие инструкции для Greenfire GF900C

Бренды по названию

Популярные бренды