manualshive.com logo in svg

Regency Greenfire GF1500L Series, Инструкция для владельца и по установке

Поделиться
Скачать
Regency Greenfire GF1500L Series Скачать руководство пользователя страница 44

44     | 

Greenfire® GF1500L-2 Gas Fireplace

installation

920-355

11/26/20

Note:  Do not screw nut in too far. If pressure doesn’t 

increase after two full turns, place the mamom-
eter on the inlet test point on the gas valve and 
check the flowing inlet pressure. Minimum = 
2.75 kPa

25.  Apply new wiring diagram decal over existing one on the bottom of 

the unit. 

26.  Turn on the gas supply and plug in the power cord.

27.  Adjust the outlet pressure. All the adjustments must be carried out 

in the following order:
a. Remove the modulator plastic cap (A) using needle-nose  

 pliers. 

b.  Maximum pressure: Turn the unit ON to its highest input rating. 

Screw in the nut (B) to increase the outlet pressure and screw it 
out to decrease it. Use a 10 mm spanner. 

Note: The maximum outlet pressure must be set to 

2.49 kPa. 

Propane / ULPG Wiring Diagram

28.  At the end of all setting and adjustment operations, check elec-

trical installation and gas leaks. 

29.  Check operation of flame control.

30.   Check for proper flame appearance and glow on logs. 

Installer Notice:

These instructions must be 

left with the appliance. 

Minimum pressure

: Remove one of the orange cables connected to the 

electric modulator. While holding the nut (B) with a wrench, screw in the 
screw (C) to increase the pressure and screw it out to decrease it. Use 
a suitable screwdriver. 

Part #:    920-356 
Size:      (File at 100%)
Color:     Black on grey
Created: 05.12.20

920-356

After carrying out all adjustments, block the setting screws with paint, 
taking care not to obstruct the breather orifice of the pressure regulator. 
Put the plastic modulator cap back on.

WARNING: To ensure correct operation of the modulator, return the 
plastic cap (A) to its original location.

NOTE: The minimum outlet pressure must be set to 1.6 kPa.

(B) Nut

(C) Screw

3

GF1500L-2

Содержание Greenfire GF1500L Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды