Regency FireGenie PG36D Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 48

background image

Regency

®

PG36D Gas Log Fireplace

6

INSTALLATION

Clearances for Bay or Flush Front

Clearance to Combustibles from:
Back

0"

(0mm)

Side

0"

(0mm)

Floor

0"

(0mm)

Minimum Clearance from Top of Unit to:
Mantel*

Minimum

7" (177mm)

Ceiling

from top of unit.

32" (1016mm)

Side Wall Clearance
Bay or Flush Front

6"

(152mm)

Horizontal Flue Clearances

Top

2" (51mm)

Side

1-1/2"

(38mm)

Bottom

1-1/2"

(38mm)

Vertical Flue Clearances

1-1/4"

(32mm)

Alcove Clearances:
Max.

Depth

36"

(914mm)

Min.

Width

48"

1219mm)

Min.

Height

72"

1829mm)

* see mantle clearance instructions (Refer
to "Combustible Mantels" & "Mantel Leg
Clearances" sections.

WARNING

Fire hazard is an extreme risk

if clearances are not adhered to.

CLEARANCES

The clearances listed below are Minimum
distances unless otherwise stated:

A major cause of chimney related fi res is
failure to maintain required clearances (air
space) to combustible materials. It is of the
greatest importance that this fi replace and
fl ue system be installed only in accordance
with these instructions.

NOTE: The minimum fl oor clearance must
be maintained from the top surface of the
carpeting, tile, etc.

Diagram 1

LOCATING YOUR

GAS FIREPLACE

1)

When selecting a location for your stove,

ensure that the clearances outlined on this
page are met.

2)

Provide adequate clearances for servicing.

3)

The appliance must be installed on a fl at,

solid, continuous surface (e.g. wood, metal,
concrete). This may be the fl oor, or raised up
on a platform to enhance its visual impact.
If the appliance is going to be installed
on carpeting, combustible linoleum tile or
other combustible material other than wood
fl ooring, the appliance must be installed on
a metal or wood panel extending the full
width and depth of the appliance.

4)

The PG36D Co Axial Flue Gas Fireplace

can be installed in a recessed position or
framed out into the room as in A, B, C, D.
See Diagram 1.

6)

The PG36D Co Axial Flue Gas Fireplace

is approved for alcove installations, which
meet the clearances listed on this page.

7)

We recommend that you plan your installation
on paper using exact measurements for
clearances and fl oor protection before
actually installing this appliance. Have an
authorized inspector, dealer, or installer
review your plans before installation.

Note: For fl ue terminations see section

" E x t e r i o r F l u e Te r m i n a t i o n
Locations."

MANUFACTURED

MOBILE HOME

ADDITIONAL

REQUIREMENTS

1)

Ensure that structural members are not cut

or weakened during installation.

2)

Ensure proper grounding using the #8

ground lug provided. See section "Wiring."

A)

Flat on Wall

B)

Flat on Wall Corner

C)

Recessed into Wall/Alcove

D)

Corner

5)

This appliance is Listed for bedroom

installations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.

«
...
4
5
6
7
8
...
»

Содержание FireGenie PG36D

















































Отзывы:

Нет отзывов

Похожие инструкции для FireGenie PG36D

Бренд: komodo Страницы: 40

Бренд: Astria Страницы: 70

Бренд: Napoleon Страницы: 40

Бренд: Napoleon Страницы: 148

Бренд: Twin-Star International Страницы: 28

SCANDIC DELUXE SDC20RC

Бренд: Dimplex Страницы: 4

Бренд: iKayaa Страницы: 2

Бренд: HWAM Страницы: 52

Бренд: Superior Страницы: 32

Бренд: pleasant hearth Страницы: 15

Бренд: IHP Страницы: 4

Бренд: Heat&Glo Страницы: 28

Бренд: Mason-Lite Страницы: 24

Бренд: Hearth and Home Technologies Страницы: 2

Бренд: Hearth and Home Technologies Страницы: 10

4Seasons Premium

Бренд: Faber Страницы: 16

Fireplace Compact

Бренд: Electralog Страницы: 47

Бренд: Klarstein Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды