Regency FireGenie PG36D Скачать руководство пользователя страница 19

Страница: 19 / 48

Regency

PG36D Gas Log Fireplace

Conversion From NG To LPG Kit #513-968

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION!!

Shut off the gas supply and unplug the
power cord.

Carefully remove the glass, logs and
lava rock.

Remove

burner.

Remove burner orifi ce with a 1/2"
wrench and discard. Use a wrench to
hold on to the elbow behind the orifi ce.

Reinstall new burner orifi ce stamped #52
and tighten.

Pull out the pilot hood by hand.

Adjust the burner aeration setting to and
re-install the burner.

10)

Open the bottom louver.

Put in the new LPG orifi ce with the allen
key. Then put back the pilot hood.

Burner Orifi ce

Pilot

Hood

Pilot

Hood

removed

Remove the pilot orifi ce with the allen
key.

LPG Conversion Kit Contains:

Qty. Part #

Description

904-390 Burner

Orifi

#52

904-529 5/32"

Allen

Key

918-590 Label

"Converted

LP"

908-528 Red

"LPG"

label

910-037 #30

ULPG

Pilot

Orifi

918-577 Instruction

Sheet

11)

Remove the front cover by undoing the 2
screws.

Front Cover

12)

Stick the conversion label "This unit has

been converted to LPG" over top of the
serial number decal.

13)

Replace the yellow "NG" label with the

red "LPG" label.

14)

Carefully pull out the control box from

underneath the fi rebox.

Note:

The control box is held in place with

velcro.

Pilot

Orifi ce

INSTALLATION

Содержание FireGenie PG36D

















































Результаты поиска

Содержание FireGenie PG36D

Отзывы:

Похожие инструкции для FireGenie PG36D

Бренды по названию

Популярные бренды

Regency FireGenie PG36D, Владельцы и установка

Результаты поиска

Содержание FireGenie PG36D

Отзывы:

Похожие инструкции для FireGenie PG36D

Бренды по названию

Популярные бренды