Regency F5102 - AUSTRALIA Скачать руководство пользователя | Manualshive

Страница: 14 / 32

background image

14

F5102 Regency Freestanding Wood Fire

INSTALLATION

FAN INSTALLATION

FAN INSTALLATION

(240V FAN)

1)

Remove the two screws from the top of the fan housing.

2)

Slide the fan up into the rear heat shield.

3)

After aligning holes, secure the fan to the rear heat shield using

the two screws removed earlier.

Note: The power cord should not be in contact with any hot

surfaces.

WARNING: FAN ASSEMBLY MUST BE DISCONNECTED FROM

THE SOURCE OF ELECTRICAL SUPPLY BEFORE

ATTEMPTING THE INSTALLATION.

FAN OPERATION

AUTOMATIC

To operate the fan automatically, push the bottom switch on the side
of the fan housing to "AUTO" and the top switch to either "HIGH" or
"LOW" for fan speed.

This will allow the fan to turn on as the stove has come up to operat-
ing temperature. It will also shut the fan system off after the fire has
gone out and the unit cooled to below a useful heat output range.

If the fan cycles on and off continuously the thermo switch sensor is
not making contact with the stove body. Remove the fan, bend the
bracket closer to the stove and re-install the fan.

MANUAL

To manually operate the fan system push the bottom switch to "MAN"
and the top switch to either "HIGH" or "LOW". This will bypass the
sensing device and allow full control of the fan.

Switching from "AUTO" to "MAN" or "HIGH" to "LOW" may be done
anytime.

CAUTION: Label all wires prior to disconnec-

tion when servicing controls. Wiring errors

can cause improper and dangerous operation.

WARNING: Electrical Earthing Instructions

This appliance is equipped with a three pronged

(earthing) plug for your protection against shock

hazard and should be plugged directly into a prop-

erly earthed three-prong receptacle. Do not cut or

remove the earthing prong from this plug.

Wiring Diagram

Fan assembly for use only with the room heater marked to indicate such use.

Ground

Fan

Fan

Ground

Green

Neutral

Live

Whit

e

Fan

Switch

Manual/

Auto

Switch

Black

Black

High

(Black)

Low

(Red)

Black

Fan Thermodisc

(normally open)

120V AC

60 Hz

240 AC

50 Hz

Earth

Earth

Earth

Earth

Earth

Earth

Earthing

«
...
12
13
14
15
16
...
»

Содержание F5102 - AUSTRALIA

































Отзывы:

Нет отзывов

Похожие инструкции для F5102 - AUSTRALIA

Бренд: Paloform Страницы: 16

Бренд: HAMPTON BAY Страницы: 48

Бренд: pleasant hearth Страницы: 30

Бренд: baltur Страницы: 88

Бренд: pleasant hearth Страницы: 87

GI 350 DV Scan 65i

Бренд: Jøtul Страницы: 2

Бренд: Essence Страницы: 3

Бренд: Napoleon Страницы: 72

Бренд: Wamsler Страницы: 84

Бренд: Charmate Страницы: 4

Бренд: Charlton & Jenrick Страницы: 4

Бренд: Superior Страницы: 24

Denali DENBR-1242

Бренд: Outdoor GreatRoom Company Страницы: 12

Бренд: pleasant hearth Страницы: 12

Бренд: IHP Страницы: 8

Woodberry 63688

Бренд: Firesense Страницы: 18

564 Artisan Face

Бренд: FireplaceXtrordinair Страницы: 4

Бренд: Fireplace Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды