Regency Classic C34, Инструкция для владельца и по установке

Страница: 34 / 48

34
|
Regency
®
CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
34
operating instructions
FIRST FIRE
7KH¿UVW¿UHLQ\RXUVWRYHLVSDUWRIWKHSDLQWFXULQJ
process. To ensure that the paint is properly cured,
LW LV UHFRPPHQGHG WKDW \RX EXUQ \RXU ¿UHSODFH
IRU DW OHDVW IRXU KRXUV WKH ¿UVW WLPH \RX XVH
LW ZLWK WKH IDQ RQ :KHQ ¿UVW RSHUDWHG WKH XQLW
will release an odour caused by the curing of the
SDLQWWKHEXUQLQJRႇRIDQ\RLOVUHPDLQLQJIURP
PDQXIDFWXULQJ6PRNHGHWHFWRUVLQWKHKRXVHPD\
JRRႇDWWKLVWLPH2SHQDIHZZLQGRZVWRYHQWLODWH
the room for a couple of hours.
The glass panel may require cleaning after the unit
has cooled down.
DO NOT ATTEMPT TO CLEAN THE
GLASS WHILE IT IS HOT.
Note: When the glass is cold and the appliance
LVOLWLWPD\FDXVHFRQGHQVDWLRQDQGIRJ
WKHJODVV7KLVFRQGHQVDWLRQLVQRUPDO
DQGZLOOGLVDSSHDULQDIHZPLQXWHVDV
the glass heats up.
OPERATING
INSTRUCTIONS
1. Read and understand these instructions before
operating this appliance.
2. &KHFN WR VHH WKDW DOO ZLULQJ LV FRUUHFW DQG
HQFORVHGWRSUHYHQWSRVVLEOHVKRFN
3. &KHFNWRHQVXUHWKHUHDUHQRJDVOHDNV
4. 0DNHVXUHWKHJODVVLQWKHGRRUIUDPHLVSURSHUO\
positioned. Never operate the appliance with
the glass removed.
5. Verify that the venting and cap are unobstructed.
6. Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have been
incorrectly positioned.
7. 7KHXQLWVKRXOGQHYHUEHWXUQHGRႇDQGRQ
again without a minimum of a 60 second wait.
8. +RRNXSUHPRWHUHFHLYHUWRZLUHPDUNHGUHFHLYHU
'XULQJ WKH ¿UVW IHZ ¿UHV D ZKLWH ¿OP
PD\ GHYHORS RQ WKH JODVV IURQW DV SDUW
of the curing process. The glass should
be cleaned
RU WKH ¿OP ZLOO EDNH RQ DQG
EHFRPH YHU\ GLႈFXOW WR UHPRYH 8VH D
QRQDEUDVLYH FOHDQHU DQG 1(9(5 FOHDQ
the glass while it is hot.
3URÀDPH
video
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
which will be located on the bottom of the appli-
ance. This remote control requires coding. See
remote control instructions for details.
NOTE: This appliance will operate during power
RXWDJHV2QO\WKHIDQZLOOQRWRSHUDWHXQWLOSRZHU
is restored. If the remote batteries in both the
handheld transmitter or receiver lose power, the
appliance can still be operated by sliding the
VZLWFK RQ WKH UHFHLYHU VZLWFK IURP 5HPRWH
WR217RWXUQRQWKHDSSOLDQFHRႇVOLGHWKH
UHFHLYHUVZLWFKIURP21WR5HPRWHRU2))
IMPORTANT: The remote control system supplied
with this appliance has several options for start-
LQJRSHUDWLQJ WKH DSSOLDQFH SOHDVH UHDG WKH
UHPRWHFRQWURORSHUDWLQJLQVWUXFWLRQVSDFNHG
ZLWKUHPRWHFRQWUROWRXQGHUVWDQGKRZWRRS
-
erate this remote system. You can download
remote functions video with the QR code below..
LIGHTING
PROCEDURE
,PSRUWDQW,IWKHSLORWGRHVQRWKROGWXUQSLORWNQRE
WR2))SRVLWLRQ:DLWPLQXWHVWRFOHDUJDV,I
\RXVPHOOJDV6723)ROORZWKHVDIHW\LQIRUPDWLRQ
above. If you don't smell gas, repeat Steps 1-6.
1 . Push in gas control knob slightly and turn to
"PILOT" position.
2
. Push in control knob all the way and hold in
until the pilot lights up. Continue to hold the
control knob in for about 20 seconds after the
pilot is lit. Release knob.
3.
Push in gas control knob slightly and turn to
"ON" position.
4
. Ensure the receiver is in the remote position.
IMPORTANT
Prior to igniting or re igniting
the pilot, remove the glass
door.
Set Switch to
Remote
Diagram 1
5 . Press and release the ON/OFF button on the
remote handheld transmitter. An audible beep
should be heard from the receiver.
ON/OFF
Button
6. The unit will turn on.
SHUTDOWN
PROCEDURE
1 3UHVV 2)) RQ WKH UHPRWH RU VOLGH UHFHLYHU
VZLWFKIURPUHPRWHWR2))
2 7XUQWKHJDVFRQWURONQREWRWKH2))SRVLWLRQ
WRWXUQRႇWKHSLORW
3LORWPD\EHVKXWRႇGXULQJSURORQJHGQRQXVH
periods to conserve fuel.
Diagram 2
Remote shown in Manual Mode on Hi