background image

12

Regency Bellerive Fireplace Insert

operating 
instructions

4)

  After about 45 minutes, when your wood 

has begun to burn strongly, adjust your draft 

control down to keep the fire at a moderate 

level.

 

WARNING:  Never build a roaring fire in 

a cold heater.  Always warm your heater 

up slowly!

5)

  Once a bed of coals has been established 

on the base of the firebox, you may adjust 

the draft control to a low setting to operate 

the unit at its most efficient mode.

6)

  During the first few fires, keep the combus

-

tion rate at a moderate level and avoid a 

large fire. Only after 5 or 6 such fires can 

you operate the heater at its maximum 

setting, and only after the metal has been 

warmed.

7)

  For the first few days, the heater will give 

off an odour from the paint. This is to be 

expected as the high temperature paint 

becomes seasoned. Windows and/or doors 

should be left open to provide adequate 

ventilation while this temporary condition 

exists.   Burning the heater at a very high 

temperature the first few times may damage 

the paint. Burn fires at a moderate level the 

first few days.

8)

  Do not place anything on the heater top 

during the curing process. This may result 

in damage to your paint finish.

Pull - Open

WARNING:  To build a fire in ignorance 

or to disregard the information con-

tained in this section can cause serious 

permanent damage to the unit and void 

your warranty!!

AIR SLIDE CONTROL

Both the primary and air wash drafts are control-

led by the control rod located on the right side 

of the unit (when facing the unit). To increase 

your draft - pull open, and to decrease - push 

closed.  All units have a secondary draft system 

that continually allows combustion air to the 

induction  ports  at  the  top  of  the  firebox,  just 

below the flue baffle.  

OPERATING 
INSTRUCTIONS

With your unit now correctly installed and safety 

inspected by your local authority, you are now 

ready to start a fire.  Before establishing your 

first fire, it is important that you fully understand 

the operation of your draft control.

CAUTION: THIS APPLIANCE MUST BE 

MAINTAINED AND OPERATED AT ALL TIMES 

IN ACCORDANCE WITH THESE INSTRUC-

TIONS.

CAUTION: THE USE OF SOME TYPES OF 

PRESERVATIVE-TREATED WOOD AS A FUEL 

CAN BE HAZARDOUS.

WARNING: ANY MODIFICATION OF THE AP-

PLIANCE THAT HAS NOT BEEN APPROVED 

IN WRITING BY THE TESTING AUTHORITY 

IS CONSIDERED AS BREACHING AS/NZS 

4013.

WARNING: DO NOT USE FLAMMABLE 

LIQUIDS OR AEROSOLS TO START OR 

REKINDLE THE FIRE.

WARNING: DO NOT USE FLAMMABLE LIQ-

UIDS OR AEROSOLS IN THE VICINITY OF 

THIS APPLIANCE WHEN IT IS OPERATING.

WARNING: DO NOT STORE FUEL WITHIN 

HEATER INSTALLATION CLEARANCES.

WARNING: OPEN AIR CONTROL AND 

DAMPER WHEN FITTED BEFORE OPENING 

FIRING DOOR.

For safety reasons and in order to avoid 

over firing of your unit do not burn your 

fire with the door open or ajar.

FIRST FIRE

When your installation is completed and in-

spected you are ready for your first fire.

1)

  Open control fully.

2)

  Open firebox door and build a small fire us

-

ing paper and dry kindling on the firebrick 

base.  Secure door on the firebox and wait a 

few minutes for a good updraft in the flue to 

establish the fire.  (Leaving the door slightly 

open will help your fire start more rapidly.)

 

CAUTION:  Never leave unit unattended 

if door is left open.  This procedure is for 

fire start-up only, as unit may overheat 

if door is left open for too long.

3)

  With the draft still in the fully open position 

add two or three seasoned logs to your  fire. 

Form a trench in the ash bed to allow air to 

reach the rear of the firebox prior to closing 

the door.

Push - Closed

Содержание Bellerive I200B-1





















Отзывы: