background image

6

 | 

Regency HZO42 (Aus) Gas Fireplace

 | 

6

installation

IMPORTANT MESSAGE  

SAVE THESE 

INSTRUCTIONS

The  HZO42  Gas  Fireplace  must  be  installed  in 
accordance with these instructions. Carefully read 
all the instructions in this manual first. Consult the 
"authority having jurisdiction" to determine the need 
for a permit prior to starting the installation. It is the 
responsibility of the installer to ensure this fireplace 
is  installed  in  compliance  with  manufacturers 
instructions and all applicable codes.

BEFORE YOU START

Safe  installation  and  operation  of  this  appliance 
requires common sense, however, we are required 
by  the  Canadian  Safety  Standards  and  ANSI 
Standards to make you aware of the following:

GENERAL SAFETY  

INFORMATION

1) 

The  installation  must  conform  with  local 
codes or, in the absence of local codes, with 

CAN/CSA-B149.1

, Natural Gas and Propane 

Installation  Code  or 

CAN/CSA-B149.2

Propane  installation  code  the  Natural  Gas 
Fuel Code, 

ANSI Z223.1/NFPA 54

 / AS5601 /

AG601

 

2)

  The  appliance  when  installed,  must  be 

electrically grounded in accordance with local 
codes, or in the absence of local codes with 
the  Canadian  Electrical  Code  CSA  C22.1or 
with the National Electrical Code, ANSI/NFPA 
70 / NZS3100 & AS5601 /AG601.

 

3)

  See  general  construction  and  assembly 

instructions. The appliance should be enclosed.

4)

  Inspect  the  burner  before  each  use  of  the 

appliance  for  blockage  and  any  signs  of 
deterioration.   

CHILDREN AND ADULTS SHOULD 
BE ALERTED TO THE HAZARDS OF 
HIGH  SURFACE TEMPERATURES, 
ESPECIALLY THE FIREPLACE GLASS 
AND FACEPLATE, AND SHOULD STAY 
AWAY TO AVOID BURNS OR CLOTHING 
IGNITION.  

THIS APPLIANCE SHALL BE USED 
ONLY OUTDOORS IN A WELL-VENTI-
LATED SPACE AND SHALL NOT BE 
USED IN A BUILDING, GARAGE OR ANY 
OTHER ENCLOSED AREA.

INSTALLATION AND REPAIR SHOULD 
BE DONE BY AN Authorised SERVICE 
PERSON. THE APPLIANCE SHOULD 
B E   I N S P E C T E D   B E F O R E   U S E 
AND AT LEAST ANNUALLY BY A 
PROFESSIONAL SERVICE PERSON. 
MORE FREQUENT CLEANING MAY 
BE REQUIRED DUE TO EXCESSIVE 
LINT FROM CARPETING, BEDDING 
MATERIAL, ETC. IT IS IMPERATIVE THAT 
CONTROL COMPARTMENTS, BURNERS 
AND CIRCULATING AIR PASSAGEWAYS 
OF THE APPLIANCE BE KEPT CLEAN.

ANY GUARD OR OTHER PROTECTIVE 
DEVICE REMOVED FOR SERVICING 
THE APPLIANCE MUST BE REPLACED 
PRIOR TO OPERATING THE APPLIANCE

WARNING: FAILURE TO INSTALL THIS 
APPLIANCE CORRECTLY WILL VOID 
YOUR WARRANTY AND MAY CAUSE A 
SERIOUS FIRE.

CLOTHING OR OTHER FLAMMABLE 
MATERIAL SHOULD NOT BE PLACED 
ON OR NEAR THE APPLIANCE.

   

DO NOT USE THIS APPLIANCE IF 
ANY PART HAS BEEN UNDER WATER. 
IMMEDIATELY CALL A QUALIFIED 
SERVICE TECHNICIAN TO  INSPECT 
THE APPLIANCE AND TO REPLACE 
ANY PART OF THE CONTROL SYSTEM 
AND ANY GAS CONTROL WHICH HAS 
BEEN UNDER WATER.

YOUNG CHILDREN SHOULD BE CARE-
FULLY  SUPERVISED WHEN THEY ARE 
IN THE SAME AREA AS THE APPLI-
ANCE.  TODDLERS, YOUNG CHILDREN 
AND OTHERS MAY BE SUSCEPTIBLE 
TO ACCIDENTAL CONTACT BURNS.  A 
PHYSICAL BARRIERS IS RECOMMEND-
ED IF THERE ARE AT RISK INDIVIDUAL 
IN THE HOUSE.  TO RESTRICT ACCESS 
TO A FIREPLACE OR STOVE, INSTALL 
AN ADJUSTABLE SAFETY GATE TO 
KEEP TODDLERS, YOUNG  CHILDREN 
AND OTHER AT RISK INDIVIDUALS OUT 
OF THE ROOM AND AWAY FROM HOT 
SURFACES. 

5)

  To prevent injury, do not allow anyone who is 

unfamiliar with the operation to use the fireplace.

6)

  Wear gloves and safety glasses for protection 

while doing required maintenance.

7)  Maximum gas inlet pressure = 3.5 kPa

8)

  Under no circumstances should this appliance 

be modified. Parts that have to be removed for 
servicing should be replaced prior to operating 
this appliance.

9)

  Installation and any repairs to this appliance 

should be done by a qualified service person. 
A professional service person should be called 
to  inspect  this  appliance  annually.  Make  it  a 
practice  to  have  all  of  your  gas  appliances 
checked annually.

10)

 Under no circumstances should any solid fuels 

(wood, paper, cardboard, coal, etc.) be used in 
this appliance.

11) The appliance and its individual shutoff valve 

must  be  disconnected  from  the  gas  supply 
piping system during any pressure testing of 
that system at test pressures in excess of 1/2 
psi (3.5kPa).

 

The appliance must be isolated from the gas 
supply piping system by closing its individual 
manual shutoff valve during any pressure testing 
of the gas supply piping system at test pressures 
equal to or less than 1/2 psi (3.5 kPa).

12)

 The  appliance  area  must  be  kept  clear  and 

free of combustible materials, (gases and other 
flammable vapours and liquids).

      

It is highly recommended to protect the 

interior from moisture (rain, snow).  Cover 

the enclosure opening when not in use.  This 

fireplace is only for use with the type of gas 

indicated on the rating plate.  This fireplace 

is not convertible for use with other gases, 

unless a certified kit is used.

13)

  Cover

 must 

be removed when burner is in

        operation.

14) When not using appliance for extended periods 

of time - turn off gas supply.

Содержание Horizon HZO42-NG













































Отзывы: