background image

26

Regency FG39 FireGenie Freestanding Gas Stove

MAINTENANCE

CAUTION:  ANY SAFETY SCREEN

OR GUARD REMOVED FOR SERV-

ICING AN APPLIANCE MUST BE

REPLACED PRIOR TO OPERAT-

ING THE APPLIANCE.

CLOTHING OR OTHER FLAMMA-

BLE MATERIAL SHOULD NOT BE

PLACED ON OR NEAR THE APPLI-

ANCE.

DO NOT USE THIS APPLIANCE IF

ANY  PART  HAS  BEEN  UNDER

WATER. IMMEDIATELY CALL AN

AUTHORIZED SERVICE TECHNI

CIAN  TO  INSPECT  THE  APPLI-

ANCE AND TO REPLACE ANY PART

OF CONTROL SYSTEM AND ANY

GAS CONTROL WHICH HAS BEEN

UNDER WATER.

WARNING:  CHILDREN  AND

ADULTS SHOULD BE ALERTED TO

THE HAZARDS OF HIGH SURFACE

TEMPERATURE  AND  SHOULD

STAY AWAY TO AVOID BURNS OR

CLOTHING  IGNITION.    YOUNG

CHILDREN SHOULD BE CAREFUL-

LY SUPERVISED WHEN THEY ARE

IN THE SAME ROOM AS THE AP-

PLIANCE.

MAINTENANCE

INSTRUCTIONS

Any maintenance required accessing the

glass door of the unit must be performed by

an  authorized  service  person.

 

1)

Always  unplug  the  power  cord  before

cleaning.  For  relighting,  refer  to  lighting

instructions. Keep the burner and control

compartment clean by brushing and vac-

uuming at least once a year. When cleaning

the logs, use a soft clean brush as the logs

are fragile and easily damaged.

2)

Clean glass (never when unit is hot), ap-

pliance,  louvres,  and  door  with  a  damp

cloth.  Never use an abrasive cleaner. The

gold louvres (and optional gold door) may

be  scratched  if  abrasives  are  used  to

clean them.

The heater is finished in a heat resistant

paint  and  should  only  be  refinished  with

heat  resistant  paint  (not  with  wall  paint).

Regency uses StoveBright Paint - Metallic

Black #6309.

3)

Make a  periodic check of burner for proper

position and condition. Visually check the

flame  of  the  burner  periodically,  making

sure the flames are steady; not lifting or

floating. If there is a problem, call an author-

ized  service  person.

4)

The appliance and flueing system must be

inspected before use, and at least annual-

ly, by an authorized field service person,

to ensure that the flow of combustion and

ventilation air is not obstructed.

During the annual service call, the burners

should  be  removed  from  the  burner  tray

and cleaned. Replace the embers - do not

block the pilot or burner ports.

5)

Keep the area near the appliance clear and

free from combustible materials, gasoline

and other flammable vapours and liquids.

6)

Verify  proper  operation  after  servicing.

GOLD-PLATED  DOORS

The  24  carat  gold  plated  finish  on  the  door

requires little maintenance, and need only be

cleaned  with  a  damp  cloth.    DO  NOT  use

abrasive  materials  or  chemical  cleaners,  as

they  may  harm  the  finish  and  will 

void  the

warranty.

  Clean  any  fingerprints  off    before

turning the unit on.

All manuals and user guides at all-guides.com

all-guides.com

Содержание FireGenie FG39-LPG





































Отзывы: