manualshive.com logo in svg

Regal Marathon Generator DVR 2400, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Regal Marathon Generator DVR 2400 Скачать руководство пользователя страница 45

45

F O R M

DVR

®

2400 and DVR

®

2500 Digital Voltage Regulator

Installation, Operation and Maintenance Manual

SB0056E

Revised

November 2018

Regal Beloit America, Inc.

100 East Randolph Street

Wausau, WI 54402-8003

www.regalbeloit.com/Brands/

Marathon-Generators

Regulation Modes (3c)

This panel contains a radio button for selecting the regulation mode:

•  

 AVR3  Regulation Mode

 is used for Automatic Voltage Regulation with 

three-phase generator voltage sensing.

•  

 AVR1  Regulating Mode

 is used for Automatic Voltage Regulation with 

single phase generator voltage sensing.

•  

 FCR  Regulation Mode

 is used for field current regulation. In this mode 

the DVR

® 

regulator will maintain a fixed level of field current.

•  

 VAR  Regulating Mode

 is used for reactive VAR regulation. This mode 

is only enabled when the VAR/PF_OFF input is open. Otherwise, the 
regulator will regulate as if AVR3 mode were selected.

•  

 PF  Regulating Mode

 is used for power factor regulation. This mode 

is only enabled when the VAR/PF_OFF input is open. Otherwise, the 
regulator will regulate as if AVR3 mode were selected.

Number of CT’s (3d)

This panel contains a radio button for selecting the number of CT’s to be 
used for current and power measurement.

•  

 Three (A, B, C) 

is used for metering of all three phase currents inde-

pendently. This sensing mode should only be selected when using three 
current transformers. This is only available on the 2500.

•   

One (B Only)

 is used for metering of phase B current only. This sensing 

mode should only be selected when using one current transformer in 
phase B. Currents for phases A and C will not be metered and power 
measurements will be based on the assumption phase B current flows 
equally in phases A and C.

•  

None

 is used if no current transformers are connected.

VR Excitation (3e)

This panel contains a radio button for disabling or enabling excitation to 
the field.

•  

 Excitation  Off

 is used to disable excitation to the generator exciter field.  

The status indicator in the header will display a “STBY” state. This state 
is recommended for making adjustments to the regulator settings.

•  

 Excitation  On

 is used to enable excitation to the generator exciter field.  

If the regulator was previously “Off,” selecting this state will initiate a 
new soft start for AVR1 and AVR3 regulation modes.

Note:

  Any changes to the regulator settings made prior to selecting “Exci-

tation On” will be lost unless they are saved to EEPROM. See the Header 
section above for details on saving settings to EEPROM.

Input Power Source (3f)

This panel contains a radio button for selecting the input power source 
type.

•  

 PM  Generator

 is selected if the input power is derived from a perma-

nent magnet generator.

Содержание Marathon Generator DVR 2400





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды