manualshive.com logo in svg

Regal genteq ECM, Руководство по обслуживанию, Страница: 2 / 58

Поделиться
Скачать
Regal genteq ECM Скачать руководство пользователя страница 2

Working on the motor with power connected may result 

in electrical shock or other conditions that may cause 

personal injury, death or property damage. 

On models 2.0 / 2.3 / 2.5 / Eon

® 

/ X13

® 

/ 3.0 / Endura

®

 Pro 

always disconnect the power from the HVAC system 

and wait at least 5 minutes before opening the motor, 

i.e. removing the two bolts from the motor control (end 

bell) and disconnecting the 3-pin plug to the motor. This 

is to allow the capacitors to dissipate for safety.

Always disconnect the power from the HVAC system 

before removing or replacing connectors, servicing 

the motor, removing the high voltage plug, and before 

reconnecting.

Disconnect AC power from the system and make sure 

the blower wheel or fan blade has come to a complete 

stop before servicing the motor.

Do not operate motor without blower wheel or fan blade 

attached. Such operation will cause the motor speed to 

oscillate up and down.

You must have the correct replacement module 

and/or motor from the manufacturer that is a direct 

replacement for the failed module and/or motor. 

USING THE WRONG MODULE and/or motor VOIDS 

ALL PRODUCT WARRANTIES AND MAY PRODUCE 

UNEXPECTED RESULTS.

Genteq does not condone the repair of any individual 

components in the motor control or motor of their 

ECM products. This practice is unsafe and may cause 

personal injury, death, or property damage.

WA R N I N G

WA R N I N G

WA R N I N G

WA R N I N G

WA R N I N G

WA R N I N G

WA R N I N G

Содержание genteq ECM



























































Отзывы:

Нет отзывов