manualshive.com logo in svg

Regal 23 OBX, Руководство пользователя

Поделиться
Скачать
Regal 23 OBX Скачать руководство пользователя страница 193

7-8

CHAPTER 7

Soak the fabric in a solution that has been mixed to the following 
proportions.: 1/2 cup of  bleach and 1/4 cup of  Ivory or Lux soap 
(liquid or soap) per each gallon of  lukewarm water. Allow the fabric 
to soak until the bleach has killed the mildew and the stains can be 
brushed out with a common kitchen scrub brush. Rinse the fabric 
thoroughly in cold water to remove all the soap. This may require 
several rinsings. Incomplete rinsing can cause deterioration of  sewing 
threads and prohibit the fabric from being properly retreated. Allow 
the fabric to dry completely. 

DO NOT STEAM PRESS OR DRY 

IN AN ELECTRIC OR GAS DRYER!

  Excessive heat can damage 

and shrink the fabric since it is heat sensitive.
This method of  cleaning may remove part of  the water and stain 
repellent that was applied to the fabric during its manufacture. It is 
recommended to retreat with such water repellency products as Apseal 
and Uniseal. We do not recommend any wax based treatments such as 
Thompson’s Water Seal or any of  the silicone products such as SC-15 
or Aqua-Tite. Wax based products prevent the fabric from breathing, 
and encourage mildew growth while the silicone products interact 
with the original 

fl

 uorocarbon 

fi

 nish and seem to cause a rapid loss 

of  water repellency. 

Clear Vinyl, Zipper & Snap Care

Never store canvas wet or in an unventilated, moist area. Always roll 
the canvas instead of  folding. This is of  particular importance on side 
curtains or any other part with the clear vinyl “glass”. Roll the top care-
fully around the bows and cover with the storage boot provided. 
The clear vinyl “glass” used in side curtains, aft curtains, visors, and 
camper enclosures is very susceptible to heat and cold. Keep vinyl 
curtains from touching metal tubing to minimize burning the vinyl.
If  the boat is stored with top, side curtains and aft curtain in place, 
heat build up inside the boat may discolor the vinyl.
To clean the clear “vinyl” glass, use a solution of  Ivory or Lux soap, 
liquid or 

fl

 akes, and lukewarm water. Allow to air dry. Never use any 

Содержание 23 OBX



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды