background image

INSTALLATION

Spring Driven Power Cord Reel

Page 2

www.reelcraft.com

Owner’s Instructions

Retractable Industrial 

Extension Cord Reel

CAUTION:

 Read all instructions and warnings before operating! 

SAVE THESE INSTRUCTIONS! READ ALL INSTRUCTIONS!

WARNING: 

To avoid serious injury or death from electrical shock or fire. 

 

 

 

Warning:

 All three screws with washers 

MUST

 be used when installing 

mounting bracket.  Eliminating one or more of the supplied hex head 

screws may allow bracket to detach allowing reel to fall causing damage 

to vehicles, injury or death.

2.56”(65mm)

2.56”(65mm)

Fig.1

Bracket hole pattern

3 - #5/16” HEX SCREWS

Bracket A

Fig.2

WALL MOUNTING  (Fig. 3 &  Fig. 4)

Fig.3

A

B

C

 Wall Mount

5Ft or Below

Fig.4

A

B

C

  Wall Mount

   Above 5Ft

CEILING MOUNTING (Fig. 5)

Fig.5

A

B

C

OPERATION

CIRCUIT BREAKER OVERLOAD PROTECTION

MAINTENANCE
WARNING: UNPLUG UNIT BEFORE PERFORMING ANY MAINTENANCE. 

Remove dirt 

and grime as soon as it accumulates. Use a soft, damp cloth and a mild soap, if 

needed. Be sure not to get the electrical plug wet. 

NEVER

 submerge any part of the 

Cord Reel in any solution to clean it. 

DO NOT USE

 solvents such as gasoline, 

turpentine, etc. to clean unit.Keep reel cord clean to assure smoothest automatic 

retraction. To clean, simply pull cord to its full length and allow to retract through a 

dampened rag. Pull out full length again and allow to retract through clean rag 

sprinkled with talcum powder. 

DRY THOROUGHLY BEFORE PLUGGING BACK INTO OUTLET.

The reset button for the circuit breaker is located on the side of Tri-Tap. If unit is 

overloaded circuit breaker will trip (black reset button will pop out).Remove 

overload, wait two minutes, then reset by pressing black button.

 Plug power cord into any 110-125V standard wall outlet.  The red LED in the 

Tri-Tap will light indicating the outlets are energized. If the indicator does not light, 

check power source. Plug up to three (3) electrical appliances into the Tri-Tap 

outlet. Pull cord to approximate desired length. Continue pulling the cord out 

slowly. When a clicking sound is heard, stop pulling the cord. The cord is now 

locked in place and is ready for use. To retract, pull the cord out slowly until the 

clicking sound stops. The cord is now unlocked and ready to retract fully. 

CAUTION!

 To avoid possible injury. 

DO NOT

 allow the cord to fly unrestricted back 

into the reel. Guide the cord back into the reel by hand to control retraction speed.    

NOTE:

 Outlet is un-switched and energized at all time. 

DO NOT OVERLOAD !

1.     Pick the approximate location for the reel within 2 1/2 ft of a 110-125V 

        Standard Ground Outlet.

2.     Locate a stud to install the mounting bracket. The bracket will be placed 

        against the wall vertically, directly over the center of the stud. 

3.     Using the bracket as a template, mark the (3) screw locations with pencil. 

        (Fig.1)

4.     Pre Drill (Pilot) the three screw holes with the use of at 1/4" drill. The depth 

        of the Pilot holes should be at least 2".

5 .    Install the bracket with the (3) provided Hex head wood screws with washers 

        using a 1/2" wrench or socket. Tighten all three until snug.

6.     The reel can now be installed into the bracket. The following installation will 

        allow smooth retraction:    

        a. When the mounting height is less than 5 ft, the reel should be positioned 

            so that the cord opening face upward (Fig. 3).     

WARNING: 

Slide the locking pin (C) thru the Mounting Pin (B) for security. 

It will prevent the mounting pin from sliding out of position.

NOTE:

 When Ceiling Mounting is to be against a steel beam, a Professional 

Installer should use minimum 1/4" bolts with lock washers or locking nuts. 

1.     Pick the approximate location for the reel within 2 1/2 ft. of a 110-125V 

        Standard Ground Outlet.

2.     Locate a joist or beam to install the mounting bracket. The bracket should be 

        placed directly over the center of the joist or beam.

3.     Using the bracket as a template, mark the (3) screw locations with pencil. 

        (Fig.1)

4.     Pre Drill (Pilot) the three screw holes with the use of at 1/4" drill. The depth of 

        the Pilot holes should be at least 2".

5.     Install the bracket with the (3) provided hex head wood screws with washers 

        using a 1/2" wrench or socket. Tighten all three until snug.

6.     The reel can now be installed into the bracket. (Fig.5)     

7.     Slide the mounting pin (B) through bracket and reel. 

1.     

DO NOT

 handle this fixture or try to plug it in when your hands are wet or 

        damp or when you are standing on a wet or damp surface or in water.

2.     This fixture 

MUST ALWAYS BE USED

 in accordance with all electri-cal and 

        safety codes and ordinances, including the most recent National Electric Code 

        (NEC) and with the Occupational Safety and Health Act (OSHA) Volume 1 on 

        General Industry Standards and Interpretations.

3.     

ALWAYS

 make certain that the power source conforms to the requirements 

        on the fixture.

4.     

ALWAYS

 disconnect the power before servicing or inspecting the fixture for 

        any reason.

5.     This fixture is 

ONLY FOR USE ON 110-125V

 and is equipped with an approved 

        3 conductor cord with a 3-prong, grounded plug. 

TO REDUCE THE RISK OF 

        ELECTRICAL SHOCK

, it should only be plugged into a properly grounded 

        3-prong outlet.

6.     

FIXTURE IS NOT WATERPROOF

 and is not intended for use in showers, 

        saunas or in potentially wet locations. 

ALWAYS

 keep this fixture away from 

        sinks, tubs, showers, etc. 

NEVER

 attempt to pick up plugged-in power tools 

        or appliances should they fall into standing water. Fatal electrocution could 

        result!

7.     This fixture comes equipped with a 3-prong grounded plug. 

DO NOT

 remove 

        the 3rd prong or otherwise try to modify the plug. If it will not fit the outlet, 

        have the proper outlet installed by a qualified electrician. Improper connection 

        of the grounding conductor can result in a risk of electrical shock.

8. 

    NEVER

 attempt to plug the fixture into a non-grounded outlet or extension 

        cord and 

ALWAYS

 be sure that the extension cord is in good electrical 

        condition.

9.     This fixture is intended for use as a general indoor power source. 

DO NOT

 use 

        in potentially dangerous locations, such as in flammable or explosive  

        atmospheres.

10.   Keep away from heating vents, radiators, or other sources of heat.

11.   

KEEP OUT OF REACH OF CHILDREN.

        b. When the mounting height is more than 5 ft, the cord opening should face 

            downward (Fig. 4). 

7.     Slide the mounting pin (B) thru bracket and reel. Slide the locking pin (C) 

        through the Mounting Pin for security.

Отзывы: