REED ST-333 Скачать руководство пользователя страница 3

reedinstruments

www

com

3

Safety

International Safety Symbols

This symbol, adjacent to another symbol or terminal, indicates 
the user must refer to the manual for further information.

This symbol, adjacent to a terminal, indicates that, under normal 
use, hazardous voltages may be present

Double insulation

Safety Notes

•  Do not exceed the maximum allowable input range of any function.
•  Do not apply voltage to meter when resistance function is selected.
•  Set the function switch OFF when the meter is not in use.

Warnings

•  Set function switch to the appropriate position before measuring.
•  When measuring volts do not switch to current/resistance modes.
•  Do not measure current on a circuit whose voltage exceeds 240V.
•  When changing ranges using the selector switch, always disconnect

 

the test leads from the circuit under test.

•  Do not exceed the maximum rated input limits.

Cautions

Improper use of this meter can cause damage, shock, injury or death. 
Read and understand this user manual before operating the meter. 
•  Always remove the test leads before replacing the battery. Inspect the 

condition of the test leads and the meter itself for any damage before 
operating the meter. 

continued ...

Содержание ST-333













Отзывы: