REED ST-333 Скачать руководство пользователя страница 12

reedinstruments

www

com

12

Data Hold

To freeze the LCD meter reading, press the data hold button. The data 
hold button is located on the left side of the meter (top button). While data 
hold is active, the HOLD display icon appears on the LCD. Press the data 
hold button again to return to normal operation.

Note:

 The HOLD feature will activate when the Backlight is turned on. 

Press the HOLD key again to exit Hold.

Backlight

Press and hold the HOLD the   key for >1 second to turn on or off the 
display backlight function. 

Note:

 The HOLD feature will activate when the Backlight is turned on. 

Press the HOLD key again to exit Hold.

Zero Button

For DCA and Capacitance Zero & Offset adjustment.

Manual Ranging

The meter turns on in the autoranging mode. Press the 

Range

 button to 

go to manual ranging. Each press of the range button will step to the next 
range as indicated by the units and decimal point location. Press and 
hold the 

Range

 button for two seconds to return to autoranging. Manual 

ranging does not function in the AC Current, Diode and Continuity check 
functions.

Battery Replacement

1. Remove the one rear Phillips head screw
2. Open the battery compartment
3. Replace the required two “AAA” batteries (UM4 R03) 
4. Re-assemble the meter

For service on this or any other REED product, contact REED Instruments 
at 1-800-561-8187 or [email protected].

Содержание ST-333













Отзывы: