background image

HIDEAWAY

ACTIVE SENSOR-FLUSH URINAL

Plumbers, please ensure a copy of the installation 
instructions is left with the end user for future reference

HIDEAWAY

ACTIVE SENSOR-FLUSH URINAL

10.0 

Diagnostic Function: 

To assist in finding faults in the electronic components 

the controller is equipped with a diagnostic function.  Follow the 

instructions below to activate this function. 

1)

Press and hold down ‘Button 1’ (flush time) for 10 to 20 seconds.

While holding the

button the LED will flash dimly, which is normal.

2) After 10 to 20 seconds release the button.

3) The LED will now flash in a bright sequence as outlined below. This LED flash

 

sequence is consecutive and check

s

 for 5 potential faults.

Between each fault check the LED will switch off for a 5 second pause.

DIAGNOSTIC FUNCTION

CORRECTIVE ACTION RESPONSE

Battery Power check:

One long flash = Battery OK

OR

Multiple flashes = Battery Power LOW

Note:

This check is for battery power controller checking only, not 

mains power

Operating correctly

Replace battery

Problem fixed

If problem cannot be resolved 

call 07 3875 2465

5 seconds pause

Pause then, Capacitive Sensor check:

One long flash = Sensor OK

OR

Multiple flashes = Capacitive Sensor not OK

Operating correctly

Ensure sensor cable is connected correctly at both plug connections.

Re-start Urinal by turning power off and then on again after 30 seconds.

Check red LED response as soon as power is switched on (see 

Commissioning). Look for 2 confirmation flushes to confirm urinal is 

functioning normally.

Problem fixed

If problem cannot be resolved 

call 07 3875 2465 for assistance

5 seconds pause

Pause then, Temperature Sensor check:

One long flash = Sensor OK

OR

Multiple flashes = Temperature Sensor not OK

Operating correctly

Ensure sensor cable is connected correctly at both plug connections.

Re-start Urinal by turning power off and then on again after 30 seconds.

Check red LED response as soon as power is switched on (see 

Commissioning). Look for 2 confirmation flushes to confirm urinal is 

functioning normally.

Problem fixed

If problem cannot be resolved 

call 07 3875 2465 for assistance

5 seconds pause

Pause then, Solenoid Valve check:

One long flash = Solenoid Valve OK

OR

Multiple flashes = Solenoid Valve is not OK

Operating correctly

Ensure Solenoid Valve is connected.

Re-start Urinal by turning power off and then on again after 30 seconds.

Check red LED response as soon as power is switched on (see 

Commissioning). Look for 2 confirmation flushes to confirm urinal is 

functioning normally.

Problem fixed

If problem cannot be resolved 

call 07 3875 2465 for assistance

5 seconds pause

Pause then, indicates Average user statistics over the past 30 

days.

1.

Flash = less than 20 usages per day

2.

Flashes = between 20 and 60 usages per day

3.

Flashes = more than 60 usages per day

Pause then, Completion of Diagnostic Mode is followed by 2 

confirmation flushes.

Informative only, no action required.

In the event of power being disconnect or switched off, all user settings and functions are retained by the Flush Control Unit. 

Button 1 

page 13 of 16

Содержание HIDEAWAY

















Отзывы: