REDSTONE RS 18Li E MA, Оригинальное руководство пользователя

Страница: 21 / 78

19
Original instructions EN
PRIOR TO INITIAL OPERATION
▪ The machine may be delivered with the wheel guard
mounted at the factory. Ensure that the wheel guard is
mounted properly and fixed reliably prior to the initial
and any following operation.
▪ The machine may be delivered with the wheel mount-
ed at the factory. Ensure that the wheel is mounted
properly and fixed reliably prior to the initial and any
following operation.
▪ Check the position of ON/OFF switch. The battery
shall be connected and disconnected to the pow-
er tool only when the switch is in OFF position. If
the battery is connected to the power tool with the
switch in ON position, the machine will not start, be-
cause the non-self starting safety (NVR) will be ac-
tuated. To start the power tool you must first switch
it off and then on again.
WARNING: Always switch off the power tool
prior to any adjustment, servicing, maintenance or
upon removing the battery.
▪ Make sure the grinding wheel diameter and thickness
do not exceed the values specified on the name plate.
The peripheral speed indicated on the wheel must not
be less than 80 m/s. The wheels must be stored ac -
cording the recommendations of the manufacturer.
▪ When using diamond cutting discs, pay attention that
the direction-of-rotation arrow on the diamond cut-
ting disc and the direction of rotation of the machine
(see direction-of-rotation arrow on the machine head)
agree.
▪ Check that the auxiliary handle is properly mounted
and reliably tightened.
FITTING AND REMOVING THE
BATTERY PACK (Fig. 1)
To remove the battery: Press release button (5) in the
indicated direction and pull the battery out of the ma-
chine body.
To insert the battery: Place the battery into the base of
the machine and slide it until it locks with an audible click.
BATTERY STATE INDICATOR (Fig.2)
Battery state can be checked on the LED display (13).
To activate the indicator, press button (12).
Battery capacity: 60 - 100%
Battery capacity: 30 - 60%
Battery capacity: < 30%
Blinking light
Battery capacity: < 20%. The battery
must be recharged.
Blinking light
Problems with battery.
The display is
activated upon pressing the trigger of
the switch. It may show one of the fol-
lowing battery states:
▪ Low battery ► Battery has to be
recharged;
▪ Temperature protection has been
actuated ► Battery must be cooled
down prior to resuming operation;
▪ Damaged or unrecognized battery
► Battery has to be replaced
Blinking light
Blinking light
(RS 18LiE MA)
Current overload:
The display is
active during operation with the ma-
chine. Upon current overload the pro -
tection switches off the machine. To
restore normal operation first switch
off and then on switch (3).
Non-self starting safety (NVR).
Indication is activated upon connect-
ing battery to machine with its switch
in ON position. To run the machine
you must first switch off and then on
switch (3).
INDICATOR FOR CURRENT SPEED
(RS 18LIE MA)
(FIG. 3)
Each pressing the speed selection button (15) whether
the ON/OFF switch is on or off results in consecu -
tive passing through the five speeds in both directions
( I - II - III - IV - V - IV - III – II - I ), which is indicated by il-
luminating the three LEDs (13) for 5 seconds. First press-
ing of button (15) results in displaying the current speed.
At next pressing the button the speed changes increas-
ingly within 5 seconds, except when the current speed
is V . In this case the change is in decreasing direction.
The recommended speed for different applications is
listed in the table below:
Material Application Operating tool Speed
Metal Removing paint Flexible backing
pad with
sandpaper
I ÷ III
Wood, metal Brush cleaning,
rust removal
Wire cup brush,
sandpaper
III
Metal,
masonry
Grinding Grinding wheel
III ÷ V
Metal Rough grinding Grinding wheel V
Metal Cutting Cutting wheel V
SWITCHING ON - SWITCHING OFF
Switching on: Push the back end of the ON/OFF switch
(3) down and then forward in the direction of the arrow
until its front end will sag, thus fixing itself.
Switching off: press the back, lifted end of switch (3)
and release it to return in its initial position.
WHEEL GUARD
WARNING: The wheel guard (8) for grinding
wheel (17) or the wheel guard (9) for cutting wheel (18)
must always be mounted on the machine!