background image

6

          

7

Quick  Start

Quick  Start

5

  Calibrate  Lens:

6

  Turn  Handheld  Control  Knob  (page  8)  and  the  motor  will  turn  in  unison.  If  you  wish  to  

reverse  motor  direction,  press  the  DIRECTION  button  on  the  Handheld.  Now  go  shoot!

A.  Auto  Calibration:  use  with  cinema  lenses  or  lenses  with  hard  stops

B.  Manual  Calibration:  use  with  DSLR  lenses  or  lenses  without  hard  stops

1

  Connect  Control  Cable  to  the  Direct  port  on  the  Basestation.  Connect  opposite  end  to  

your  controller  (Handheld,  Fingerwheel,  etc.).  Use  cable  part  #2-­100-­0012  for  direct  
tethered  connect  to  Remote  Handheld.  Use  cable  part  #2-­100-­0025  for  Fingerwheel.

2

  Follow  steps  2-­6  of  Wireless  Set-­Up  section.

Wired  Set-­Up

Congratulations  on  your  purchase  of  the  microRemote  system.  The  microRemote  system  is  
a  versatile,  expandable,  remote  focusing  system.  This  booklet  will  guide  you  through  the  
setup  and  function  of  each  component  that  is  available  for  this  system  at  this  time.  You  may  
not  have  purchased  some  of  the  items  described  within,  as  this  manual  is  comprehensive  
of  the  entire  microRemote  System.  Please  review  this  entire  manual  before  attempting  your  
initial  setup.

Your  New  microRemote

  

Quick  Start  Guide  

1

  Insert  batteries  into  Handheld  unit  (page  9).  Turn  on  Power  Switch.  All  LEDs  should  flash  

in  sequence  and  then  in  unison,  then  settle  into  their  operational  mode.

a.  Press  the  CAL  button  on  the  Basestation  (page  10)  to  enter  manual  calibration.
b.  The  CAL  indicator  LED  will  blink.  Press  the  UP  button  until  you  reach  the  end  of  

the  lens'  focus.  Use  UP/DOWN  if  you  need  to  refine  the  position.

c.  Press  SET  to  set  first  focus  point.  The  opposite  LED  will  now  blink,  press  the  

corresponding  arrow  button  until  you  reach  the  opposite  end  of  the  lens.  

d.  Press  SET  to  set  the  second  focus  point.  Your  lens  is  now  calibrated.    

Wireless  Set-­Up

2

  Plug  in  7  pin  Motor  Cable  (page  19)  to  Motor  and  Basestation.  The  larger  right  angle  

connector  connects  to  the  Motor.  See  page  12  for  proper  cable  installation.      

3

  Apply  power  to  Basestation  (via  your  wall  mount,  external  battery,  etc.)  being  careful  NOT  

to  insert  the  Power  connector  into  the  Motor  port  (page  10).    The  motor  light  will  then  
blink,  indicating  the  Basestation  is  ready  for  motor  calibration.

4

  Set  your  lens  focus  ring  to  the  center.  Mount  motor  to  rig  in  the  appropriate  position  (page  

12,13).  Press  the  drive  gear  against  the  lens  gear  using  light  pressure  until  teeth  
interlock.  

Make  sure  the  motor  is  positioned  somewhere  in  the  middle  of  the  lens'  focus  range.  
Avoid  starting  at  either  end  of  the  focus.

Press  the  

AUTO

  button  on  the  Basestation  (page  10).  The  motor  will  travel  from  

one  end  of  the  lens  to  the  other,  then  return  to  the  position  of  the  controller.  Your  
lens  is  now  calibrated.

Содержание microRemote













Отзывы: