RMC-M96
9
GBR
UKR
KAZ
heating)”). Depending on the selected programme, the timer will begin countdown
immediately or upon reaching the required temperature in the bowl.
In certain automatic programs countdown starts only when the device reaches its operating
parameters. E.g. in “ПАР” program the countdown of the program begins only when the water
comes to a full boil providing enough steam. The
indicator will flash on the display when
the device reaches the operating parameters
10. An audible signals will be produced to indicate that cooking cycle is complete. When the
programme or auto-heating function ends, the display will show the word “End” for a few
seconds and then the device will go into waiting mode, then the appliance will go into
the standby mode.
To interrupt cooking process at any stage, to cancel set program or the Keep Warm function
press and hold down
“Разогрев/Отмена”
button.
To achieve a good result refer to the recipes included in the REDMOND RMC-М96 cookbook,
designed specifically for this model. You can also find corresponding recipes on www.redmond.
company.
Setting Cooking Time
The multicooker allows manually adjusting the cooking time, set by default for each program
(except EXPRESS). Time adjustment range and interval depend on the program of cooking
selected (see “Summary Table of Cooking Programs (Default Settings)”).
1. Press the
“Время” button, the hour value will start flashing on the display.
2. Set the hour value with the and buttons. Switching takes place in a circle. Press and hold
the corresponding button down to scroll through the digits.
3.
To save the changes and set the minute timer, press the “Время” button.
4. In the same way set the minute value. If you do not press the buttons on the panel for a
few second, the changes will be saved automatically (the numbers on the display will
stop flashing). To return to setting hours, press the “Время” button before it auto-saves.
“МУЛЬТИПОВАР” programme – setting cooking temperature before starting
When using the “МУЛЬТИПОВАР” programme you can adjust both time and temperature before
the start. Temperature range – 35 to180°С with a 5°С interval.
1.
Press the “Температура” button, the default temperature value will start flashing on the
display.
2. Set the temperature value with the and buttons. Switching takes place in a circle.
Press and hold the corresponding button down to scroll through the digits.
3. Do not press the buttons on the control panel a few seconds, settings will be saved
automatically (the display will start showing the cooking time again).
For overheat protection when setting the cooking temperature higher than 150°С the maximum
programme operating time is limited to two hours
If you use the
“МУЛЬТИПОВАР”
program for boiling the water (for example, when cooking
products), it is FORBIDDEN to set the cooking temperature above 100°C.
Time Delay Function
This function allows you to set the time after which the selected cooking program will start.
1. Press the
“Отсрочка” button. The
indicator will come on, the hour value will start
flashing on the display.
2. Set the hour value with the and buttons. Switching takes place in a circle.
Press
and hold the corresponding button down to scroll through the digits.
3.
To save the changes and set the minute timer, press the “Отсрочка” button.
4. In the same way set the minute value. If you do not press the buttons on the panel for a
few second, the changes will be saved automatically (the indicator will switch off and
the display will start showing the cooking time again). To return to setting hours, press
the “Отсрочка” button before it auto-saves.
This function is not available on all programmes (see “Summary Table of Cooking Programs
(Default Settings)”).
While the Time Delay function is operating, the display will show a countdown timer to the time
the programme begins, the selected program indicator and
indicator, “Разогрев/Отмена”
and “Старт” button indicators is lit.
If the auto-heating function is active, the light will be lit
(see “Keep Warm Function (automatic heating)”).
While the Time Delay function is operating, the display will show a countdown timer to the
time the programme begins. Press the “Отсрочка” button, on the display for a few seconds to
show the set cooking time.
The device will emit a sound when the time is up, and indicators will turn off. The chosen
cooking programme will begin.
It is not recommended to use Time Delay function if dairy and other perishable products are
being used (eggs, fresh milk, meat, cheese etc.).
MASTERCHEF LITE function
Open even more opportunities for culinary creativity with the new MASTERCHEF LITE feature!
If the “МУЛЬТИПОВАР” program allows you to set the parameters of the program before it
starts, then using the MASTERCHEF LITE function, you can change the settings directly in the
cooking process.
You can always configure the work of any program so that it corresponds to your wishes. Does
the soup boil away? Does the milk porridge “runs away”? Are the steamed vegetables cooked
for too long? Change the temperature or cooking time without interrupting the program, as
if you were cooking on the stove or in the oven.
The MASTERCHEF LITE function allows you to change the cooking time and temperature while
any automatic programme is operating (excluding “ЭКСПРЕСС” programme).
Содержание RMC-M96
