Redmond RHF-3316, Руководство пользователя

Страница: 9 / 12

RHF-3316
9
ENG
4. For manual switching to standby mode, press the button on the appliance panel or
remote control, the body backlight will turn off. When finish using the appliance, unplug
it from the mains and drain the water remaining in the tank and working chamber.
“Warm Steam” function
When using this function, the water is heated up to 80°C before being funneled to the ultra­
sonic membrane, and warm steam with a temperature of 40–45°C comes out of the humidi­
fier. Heating (effect of pasteurization) kills most of the known pathogenic bacteria and micro­
organisms. In addition, due to the increased temperature, the vaporization in the appliance
occurs more intensively, thus, warm steam humidifies the air in the room faster and distributes
aromatic oils more efficiently (when using the aromatization function).
To enable/disable the “Warm Steam” function, press the
button on the control panel or
remote control. When the function is enabled, the indicator on the display lights up.
Ionization function
The appliance is equipped with a built­in ion generator. Humidified ionized air contributes to
faster dust settling, which facilitates wet cleaning and increases its efficiency, and also helps
to clean the air of germs and allergens. In addition, ionized air improves well­being and good
sleep, reduces fatigue.
To enable/disable the ionization function, press the
button on the control panel or remote
control. When the function is enabled, the indicator on the display lights up.
Aromatization function
Before turning on the appliance, remove the special tray with a sponge from the hollow in
the appliance base and apply a few drops of aromatic oil on it to achieve the effect of aroma­
tization. After use or to stop aromatization, remove the sponge tray and rinse it under running
water, then dry it completely at room temperature before inserting it into the appliance.
Humidification intensity adjustment
You can adjust the intensity of humidification by pressing the button on the control panel
or remote control. The indicator on the display shows the selected level:
—
— minimum intensity;
— —
— medium intensity;
— — — — maximum intensity.
Humidity level adjustment
You can set the desired humidity level between 40% and 80% in 5% increments. When the
selected value is reached, the appliance automatically turns off.
Select the desired value by pressing the
button on the control panel or the button on
the remote control; switching is performed circle­wise. The indicator will switch on. The
selected value on the display will blink several times and be automatically saved; the display
will show again the current humidity level and temperature.
If the selected humidity level is lower than the humidity level in the room, the appliance will
turn off after 2 minutes of operation.
Upon reaching the set humidity level, the appliance will automatically turn off the steam
output; the humidification intensity indicator will turn off. If the humidity level in the room
drops below the set level, steaming will be resumed. To disable the function of maintaining
the set humidity level, by pressing the button on the control panel or on the remote
control, select the value “ — — ”. The indicator will go off.
Automatic mode
In automatic mode, the appliance maintains the humidity in the room at the level of 55–68%,
by selecting the most suitable humidification mode.
To enable/disable automatic mode, press and hold the
button on the control panel for a
few seconds or press the button on the remote control. In automatic mode, the indi ­
cator is lit on the display.
Night mode
In night mode, the body backlight and the indication on the display are turned off. To switch
to night mode, press the button on the control panel or remote control; the indicator on
the display will light up, all other indications will go out. Approximately 20 seconds after, the
indicator will turn off. To disable the night mode, press any button on the control panel or
remote control (except the button).
Sleep timer
You can set the appliance shutdown time in the range from 1 to 10 hours in 1 hour increments.
To set the timer, press the button on the control panel or remote control; switching is
performed circle­wise. After the selected period of time, the appliance will automatically switch
to sleep mode. When the function is enabled, the “Н” indicator on the display lights up.
When set to “C”, the timer will be disabled.
III. CLEANING AND MAINTENANCE
General cleaning recommendations
Before cleaning the appliance, ensure it is unplugged. Drain water from the tank and compartments
in the base. Clean the housing with a soft cloth or sponge. You can use mild soap for cleaning. We
recommend you to wipe the surface dry to avoid water stains and residues on the housing.
DO NOT immerse the appliance in water or wash under running water!
Rinse the water tank with clean running water and wipe it with a soft dry cloth. Carefully clean
the membrane with the brush included. Dry the base and water tank after cleaning. If the
appliance is used continuously, perform this cleaning once in two days.
DO NOT use a sponge or tissue with hard or abrasive surface or abrasive pastes. Do not use
any chemically aggressive substances.