PSZ2465S
U
S
6. Set up
■
MOUNTING ENGINE (SE1)
1. Insert the driveshaft housing (1) into
the clutch housing (2) until it bottoms,
and align the positioning holes on the
both housings and screw in the locking
bolt (3) firmly.
2. Fasten the clamp securely with 2
screws (4).
(1) Driveshaft housing
(2) Clutch housing
(3) Locking bolt
(4) Screws
■
CONNECTING THROTTLE WIRE
1. Remove the air cleaner cover.
2. Connect the end of the throttle wire to
the joint on the top of the carburetor.
(SE2)
■
CONNECTING SWITCH WIRES
• Connect the switch wires between the
engine and the main unit. Pair the wires
of the same color.
■
INSTALLING THE TRANSMISSION
(SE3)
1. Before installing the transmission to the
driveshaft housing, rotate the driveshaft
by hand to check the driveshaft is
engaged with the clutch drum in the
clutch housing.
2. Remove the fastening bolt (4) and the
locking bolt (5) from the transmission.
3. Insert the driveshaft housing into the
transmission.
4. Align the screw hole (3) with the hole
for the locking bolt, and screw in the
locking bolt (5) firmly.
5. Screw in the fastening bolt (4) to fix the
transmission on the driveshaft housing.
(1) Driveshaft housing
(2) Transmission
(3) Screw hole
(4) Fastening bolt
(5) Locking bolt
■
ATTACHING THE GUIDE BAR AND
CHAIN
A standard package contains the items as
shown below. (SE4)
(1) Guide bar
(2) Saw chain
(3) Transmission
(4) Sprocket
(5) Chain tension adjust screw
(6) Mounting nut
(7) Chain tensioner pin
(8) Chain cover
SE1
(1)
(3)
(4)
(2)
SE2
(1)
(3)
(4)
(2)
(5)
SE3
SE4
(1)
(2)
SE5
(3)
SE6
(1)
(a)
(b)
SE7
(1)
SE8
Install the guide bar and the saw chain on
the transmission as follows.
The saw chain has very sharp edges.
Use protective gloves for safety.
1. Loosen a nut and remove the chain
cover.
2. Mount the guide bar then fit the saw
chain around the bar and
sprocket.(SE5)
3. Fit the chain tensioner pin into the
lower hole (1) of the guide bar, then
install the chain cover, and fasten the
mounting nut (3) to finger tightness.
(SE5)(SE6)
(1) Hole
(2) Moving direction
(3) Mounting nut
Pay attention to the correct direction of
the saw chain
4. Adjust the chain tension by turning the
chain tension adjust screw until the saw
chain does not sag from the underside
of the bar. (SE 7)
(1) Chain tension adjust screw
(a) Loosen
(b) Tighten
5. Tighten the mounting nut securely with
the bar tip held up (TORQUE: 8.9~11.7
N.m./90~120 kg-cm). Then check the
chain for smooth rotation and proper
tension while moving it by hand. If
necessary, readjust the chain tension
with the chain cover loose. (SE8)
(1) Tighten
It is very important to maintain the
proper chain tension. Rapid wear of
the guide bar or the chain coming off
easily can be caused by improper
tension. Especially when using a new
chain, take good care of it since it
should expand when first used.
■
BALANCE UNIT
1. Put on strap and attach unit to strap.
2. Depending on the working posture,
slide clamp up or down until unit
balances and the strap fits your body.
WARNING
WARNING
WARNING
US-9
