RedMax GZ25N Скачать руководство пользователя страница 6

5

STRATO CHARGED ENGINE

 

GZ25N

2. SPECIFICATIONS AND TECHNICAL DATA

Item     

Unit

Specifications

Remarks

Engine GZ25N

Engine Type  

Air cooled 2-stroke single cylinder 
piston valve gasoline engine 

Cylinder Bore x Stroke

mm (in.)

ø34 x 28 (1.339 x 1.102)

Displacement  

cc (cu.in.)

25.4 (1.6)

Effective Compression Ratio  

8.0

Fuel

Mixture of 87 octane or above unleaded   Use JASO FC 
gasoline and RedMax 2-cycle engine oil  or ISO EDG  
(ratio 50 :1) or quality oil for air cooled grade 2-cycle
2-cycle engines (ratio 32:1).

engine oil.

Carburetor   

Type

   

Diaphragm Rotary valve

            

 

Model

Walbro WYA-1B

Starting Method

Recoil starter

Ignition System       

CDI with automatic timing advance 
system. 

Ignition  Timing

°

/ rpm

35 / 7000

Spark Plug

NGK CMR7A

Stopping Method             

  

Primary coil short-circuiting

Cooling  System  

Forced Air Cooling

Air Cleaner    

Dry Type

Output Axle Rotation Direction   

Counterclockwise 

 (View from 

  

   PTO)

Clutch Type  

Automatic Centrifugal Clutch
(Sintered Clutch Shoe)

Overall Size 

Engine GZ25N for

Engine GZ25N2 for 

exept SGCZ2500S

SGCZ2500S

  

Length

mm (in.)

271 (10.67)

188 (7.40)

             

Width

mm (in.)

223 (8.78)

223 (8.78)

             

Height

mm (in.)

248

9.76

248

9.76

Dry Weight

kg (lbs.)

3.1

6.8

2.8

6.2

Fuel tank Capacity

 lit. (fl,oz)

0.65

22.0

Operating Speed

rpm

6000    10000

Idling Speed

rpm

3000 

±

200

Clutch Engagement Speed

rpm

4000 

±

200

No-Load Max Speed

rpm

10000

With Standard 
Head

Max Output

HP(kW) / rpm

1.2 (0.9) / 7500

Max Torque

kg•m(in.lbs) / rpm

0.12 (10.4) / 6500

Full Load Fuel Consumption

g/HP.h(g/kW.h)

330 (449)

Содержание GZ25N


























Отзывы: