RedMax EXTREME EXZ2500S-BC Скачать руководство пользователя страница 47

Страница: 47 / 64

12. Parts list

NOTE :

1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or

replacement.

2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the

use of any parts other than those specified by the company.

3. When placing parts orders for repair and/or replacement, check if the model name and the

serial number are applicable to those specified in the parts list, then use parts number

described in the parts list.

4. The contents described in the parts list may change due to improvement.

5. The parts for the machine shall be supplied seven (7) years after the machine is

discontinued. [It is possible that some specific parts may be subject to change of their

delivery term and list price within the limit of seven (7) years after the machine is

discontinued. It is also possible that some parts may be available even after the limit of

seven (7) years.]





EXtreme™

Mar. 2003

EXZ2500S-BC



EXZ-PU









EX-BC









ENGINE



EX-LRT

(ATT)

EX-PS

(ATT)

EX-HE

(ATT)

EXZ-PU

302845 and up

EX-BC

302960 and up

EX-LRT

000531 and up

ENGINE UNIT 352001 and up

EX-PS

000000 and up

EX-HE

000101 and up

APPLICABLE SERIAL NUMBERS :

Содержание EXTREME EXZ2500S-BC

































































Результаты поиска

Содержание EXTREME EXZ2500S-BC

Отзывы:

Похожие инструкции для EXTREME EXZ2500S-BC

Бренды по названию

Популярные бренды

RedMax EXTREME EXZ2500S-BC, Руководство владельца/оператора

Результаты поиска

Содержание EXTREME EXZ2500S-BC

Отзывы:

Похожие инструкции для EXTREME EXZ2500S-BC

Бренды по названию

Популярные бренды