RedMax EXTREME EXZ2500S-BC Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 64

RedMax EXTREME EXZ2500S-BC Скачать руководство пользователя страница 17

6. Set up

(EX-PS only)

(1)

(2)

(3)

(4)

(5)

EX-PS
SE1

EX-PS
SE2

EX-PS
SE3

■

ATTACHING THE PRUNING MECHANISM (SE1)

1. Remove the cap on the end of the main pipe.
2. Remove the screw screwed into the end of the

gear case.

3. Insert the end of the gear case into the main

pipe.

4. Line up the hole on the end of the gear case into

which the screw is to be inserted with the hole
on the main pipe, and screw the screw firmly in.

5. Using a wrench, screw in the bolt provided to fix

the mechanism into place.

(1) Main pipe
(2) Gear case
(3) Screw hole
(4) Fastening bolt
(5) Bolt

A standard package contains the items as shown
below. (SE2)

(1) Guide bar
(2) Saw chain
(3) Gase case
(4) Sprocket
(5) Chain tension adjust screw
(6) Nut
(7) Chain tensioner nut
(8) Chain cover

Install the guide bar and the saw chain on the gear
case as follows.

The saw chain has very sharp edges. Use
protective gloves for safety.

1. Loosen a nut and remove the chain cover.
2. Mount the guide bar then fit the saw chain

around the bar and sprocket. (SE3)

Pay attention to the correct direction of the saw
chain

WARNING

WARNING



17



«
...
15
16
17
18
19
...
»

Содержание EXTREME EXZ2500S-BC

































































Отзывы:

Нет отзывов