background image

Install LDA- H

Drawing No. LP0673

Revised 08 2021

1

GENERAL DESCRIPTION

The Large Display is a versatile display available as a DC volt, current, 

or process meter with scaling, serial communications and dual relay 

outputs. The 5  digit displays are available in either 2.25" or 4" high red 

LED digits with adjustable display intensities. The 2.25" high models are 

readable up to 130 feet. The 4" high models are readable up to 180 feet. 

Both versions are constructed of a NEMA 4X/IP65 enclosure in light 

weight aluminum.

All models also come with dual Form C relay outputs and RS232 / 

RS485 serial communications.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear 

in this document or on equipment must be observed to ensure personal 

safety and to prevent damage to either the device or equipment 

connected to it. 

Do not use these products to replace proper safety interlocking. No 

software-based device (or any other solid-state device) should ever be 

designed to be responsible for the maintenance of personnel safety or 

consequential equipment not equipped with safeguards. Red Lion 

disclaims any responsibility for damages, either direct or consequential, 

that result from the use of this equipment in a manner not specified.   

ORDERING INFORMATION

MODEL NO. DESCRIPTION

PART NUMBER

LD2A

2.25" High 5 Digit Red LED Volt/Current Meter w/ 

Relay Output and RS232/RS485 Serial Comms

LD2A05P0

LD4A

4" High 5 Digit Red LED Volt/Current Meter w/ 

Relay Output and RS232/RS485 Serial Comms

LD4A05P0

LD Plug

Cord Grip Plug for LD models  *

LDPLUG00

* Required to maintain Type 4X/IP65 specification, if end plate cord grip does not 

have cable installed.

SPECIFICATIONS

1. 

DISPLAY

: 5 digit, 2.25" (57 mm) or 4" (101 mm) intensity adjustable 

Red LED (-99999 to 99999)

2. 

POWER REQUIREMENTS

:

AC POWER: 50 to 250 VAC 50/60 Hz, 26 VA

DC POWER: 21.6 to 250 VDC, 11 W

DC Out: +24 VDC @ 100 mA if input voltage is greater than 50 VAC/

VDC +24 VDC @ 50 mA if input voltage is less than 50 VDC

Isolation: 3000 Vrms for 1 min. to all inputs and outputs

3. 

INPUT RANGES

: Jumper Selectable

D.C. Voltages

: 200 mV, 2 V, 20 V, 200 V, 10 V

INPUT 

RANGE

ACCURACY @ 

23 

°

C LESS 

THAN 85% RH

INPUT 

IMPEDANCE

MAX 

INPUT 

SIGNAL

RESOLUTION

TEMP. 

COEFFICIENT

200 mV

0.1% of span 1.033 M

75 VDC

10 µV

70 ppm /°C

2 V

0.1% of span 1.033 M

75 VDC

0.1 mV

70 ppm /°C

10 V

0.1% of span 1.033 M

250 VDC

1 mV

70 ppm /°C

20 V

0.1% of span 1.033 M

250 VDC

1 mV

70 ppm /°C

200 V

0.1% of span 1.033 M

250 VDC

10 mV

70 ppm /°C

D.C. Currents

: 200 

µ

A, 2 mA, 20 mA, 200 mA

INPUT 

RANGE

ACCURACY @ 

23 

°

C LESS 

THAN 85% RH

INPUT 

IMPEDANCE

MAX 

INPUT 

SIGNAL

RESOLUTION

TEMP. 

COEFFICIENT

200 µΑ

0.1% of span

1.111 K

15 mA

10 nA

70 ppm /°C

2 mA

0.1% of span

111 

50 mA

0.1 µA

70 ppm /°C

20 mA

0.1% of span

11 

150 mA

1 µA

70 ppm /°C

200 mA 0.1% of span

500 mA

10 µA

70 ppm /°C

D.C. Process

: 4 to 20 mA, 1 to 5 VDC, 0/1 to 10 VDC

INPUT RANGE

SELECT RANGE

4 - 20 mA

Use the 20 mA range

1 - 5 VDC

Use the 10V range

1 - 10 VDC

Use the 10V range

4.

 OVERRANGE/UNDERRANGE INDICATION:

Input Overrange Indication

:  “

OLOL

”.

Input Underrange Indication

:  “

ULUL

”.

Display Overrange/Underrange Indication

: “

.....

”/“-

.....

” 

CAUTION: Risk of Danger.

Read complete instructions prior to 

installation and operation of the unit.

CAUTION: 

Risk of electric shock.

The protective conductor terminal is bonded to conductive 

parts of the equipment for safety purposes and must be 

connected to an external protective earthing system.

  2.25" & 4" HIGH RED LED DIGITS

  PROGRAMMABLE SCALING AND DECIMAL POINTS

  PROGRAMMABLE USER INPUT

  DUAL 5 AMP FORM C RELAY

  ALUMINUM NEMA 4X/IP65 CASE CONSTRUCTION

  RS232/RS485 SERIAL COMMUNICATIONS

  UNIVERSALLY POWERED

MODEL LD - Large DC Volt/Current/Process Display

AIR PRESSURE STABILIZATION VENT

(57.15)

2.25

X
Z

Y

DIMENSIONS  In inches (mm)

22 (558.8)

12 (304.3)

Z (Center)

7.875 (200)

26 (660.4)

LD4A05P0

4 (101.6)

16 (406.4)

LD2A05P0

Y (Height)

X (Length)

PART 

NUMBER

CC

US LISTED

US LISTED

UL

R

IND. CONT. EQ.

E137808

CC

US LISTED

US LISTED

UL

R

PROCESS CONTROL EQUIPMENT

E179259

Содержание LD Plug

















Отзывы: