Redline Communications RedMAX AN100U Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 178

background image

3-15

Chapter 3 Indoor Equipment Maintenance

Redline Communications Inc. Confidential and Proprietary

Step 2

From the Main menu select Interface Configuration > Wireless Interface.

The Wireless Interface Configuration page is displayed. You can review this page to
view RF, PHY and MAC settings for the sector controller.

Step 3

Update the parameters to match the installed radio. Refer to the RedMAX AN100U/UX
Base Station User Guide for detailed information on setting these parameters.

Step 4

Reboot the sector controller in order for your changes to take effect. See “Rebooting the
Devices” on page 3-2.

Step 5

Once the device has completed the reboot operation, select Interface Configuration >
Wireless Interface and verify that your changes have taken effect.

Step 6

Click the Enable RF button to re-enable the RF interface.

AN100U/UX CLI

Step 1

Login to the CLI as outlined in “Connecting to the Sector Controller Command Line
Interface” on page 2-5.

Step 2

Review the existing wireless configuration:

interfaces wireless show

Step 3

You can now view a dynamically updated screen of statistics. Press any key to exit
monitoring mode.

Step 4

Update the parameters to match the installed radio. Refer to the RedMAX AN100U/UX
Base Station User Guide for detailed information on determining the values and setting
these parameters in the CLI.

Step 5

Reboot the sector controller in order for your changes to take effect. See “Rebooting the
Devices” on page 3-2.

Step 6

Once the device has completed the reboot operation, review the wireless configuration to
verify that your changes have taken effect:

interfaces wireless show

«
...
45
46
47
48
49
...
»

Содержание RedMAX AN100U



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RedMAX AN100U

Бренд: Daga Страницы: 28

BIESEMEYER 78-955

Бренд: Delta Страницы: 12

Бренд: Samsung Страницы: 88

Бренд: Samsung Страницы: 215

Бренд: D-2 Incorporated Страницы: 28

Бренд: D+H Страницы: 12

Бренд: Lastolite Страницы: 3

Бренд: QIMMIQ Страницы: 16

Бренд: QA1 Страницы: 10

Бренд: RaceChip Страницы: 20

Бренд: V-TAC Страницы: 4

Бренд: Hobo Страницы: 7

Бренд: Doug Thorley Headers Страницы: 5

Бренд: A&D Страницы: 4

Canon PowerShot A700

Бренд: Ikelite Страницы: 6

Бренд: CAME Страницы: 4

Exta Life RCR-21

Бренд: Zamel Страницы: 9

Бренд: Datavideo Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды