Redline Communications RedMAX AN100U Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 178

background image

2-5

Chapter 2 Overview

Redline Communications Inc. Confidential and Proprietary

If you have configured another local or network IP address you must use that address.

Step 3

When the command prompt screen appears, login using the following values:

Username: admin

Password: admin

You are now connected to the sector controller and can display and modify its current
configuration. Refer to the RedMAX AN100U/UX Base Station User Guide for details on
using the sector controller Web client.

Connecting to the Sector Controller Command Line Interface

The sector controller also provides a command line interface, through which you can
display and modify the device’s current configuration. You require Telnet or a similar
application to connect to this interface.

You must have connectivity from your computer to the sector controller before you can use
this procedure.

Step 1

Open the Windows Start Menu and select Run:

Step 2

Enter the following command:

telnet 192.168.101.3

If you have configured another local or network IP address you must use that address.

Step 3

When the command prompt screen appears, login using the following values:

Username: admin

Password: admin

You are now connected to the sector controller CLI. Refer to the RedMAX AN100U/UX
Base Station User Guide for detailed information on using the CLI.

Accessing the Debug Mode

Debug mode is used for factory test and advanced troubleshooting. Logging in to the Web
GUI or Telnet session using the debug user name and password provides access to
advanced configuration controls. Debug mode should be used only under the explicit
direction of Redline field service or their representatives. It is recommended to change the
debug mode default password to restrict access to this feature.

Step 1

Open the Windows Start Menu and select Run:

Step 2

Enter the following command:

telnet 192.168.101.3

If you have configured another local or network IP address you must use that address.

«
...
15
16
17
18
19
...
»

Содержание RedMAX AN100U



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RedMAX AN100U

Бренд: Canon Страницы: 10

Бренд: Manfrotto Страницы: 2

Бренд: Garmin Страницы: 26

Бренд: Garmin Страницы: 33

Бренд: Garmin Страницы: 167

Бренд: GARO Страницы: 23

Бренд: Xerox Страницы: 10

Бренд: M-Audio Страницы: 14

Бренд: Aroflora Страницы: 36

Бренд: Mamiya Страницы: 6

Бренд: DigiTech Страницы: 15

Бренд: My Child Страницы: 12

Marble + Brass 2743412

Бренд: West Elm Страницы: 3

Бренд: Fullwat Страницы: 9

Бренд: IBASE Technology Страницы: 100

Бренд: JUGS Страницы: 17

Бренд: LEGRAND Страницы: 2

S2000 Windscreen Camera Mount

Бренд: Modifry Products Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды