Redexim Verti-Drain 1513 Скачать руководство пользователя страница 9

Страница: 9 / 26

1.0 TECHNICAL DATA

Model

1513

1517

Working width:

1.32 m (52”)

1.76 m (69”)

Working depth:

Up to 150 mm (6”)

Tractor speed measured at 540 rpm on PTO:

Pitch 55 mm (2.6”)
Pitch 90 mm (3-1/2”)
Pitch 125 mm (5.1”)

Up to 1.8 km/h (1.1 mph)
Up to 2.9 km/h (1.8 mph)
Up to 4.1 km/h (2.5 mph)

PTO rpm: (max.)

Up to 540 rpm

Weight:

425 kg (937 lbs)

520 kg (1146 lbs)

Pitch between pins:

55 mm (2-1/8”)

Pitch in driving
direction:

25 – 125 mm (1” – 7.5”)

Recommended tractor: 25 HP with minimum lift

capacity of 650 kg
(1450 lbs)

28 HP with minimum lift
capacity of 750 kg
(1653 lbs)

Maximum capacity:

Pitch 55 mm (2.6”)

     Pitch 90 mm (3-1/2”)

Pitch 125 mm (5.1”)

Up to 2388 m²/hr (25703
ft²/hr)
Up to 3907 m²/hr (42059
ft²/hr)
Up to 5427 m²/hr (58416
ft²/hr)

Up to 3136 m²/hr (33759
ft²/hr)
Up to 5132 m²/hr (55242
ft²/hr)
Up to 7128 m²/hr (76725
ft²/hr)

Dimensions:

1610 x 970 x 780 mm
(63.4” x 38.2” x 30.7”)

2050 x 970 x 780 mm
(80.7” x 38.2” x 30.7”)

Maximum tine
diameter:

Solid :

12 x 150 mm (1/2”x 6”)
Hollow:

19 x 150 mm (3/4” x 6”)

Solid :

12 x 150 mm (1/2”x 6”)
Hollow:

19 x 150 mm (3/4” x 6”)

Three-point hitch:

3-point CAT 1

Gear casing oil:

80W90 – 0.9 liter

Lubricant:

EP 2

Standard components: Set solid tines 12 x 150 (1/2”x

6”) with accompanying tine
holders.
Trunk with tools and user
manual.
PTO.
Support legs.

Set solid tines 12 x 150 (1/2”x
6”) with accompanying tine
holders.
Trunk with tools and user
manual.
PTO.
Support legs.

Options:

Hollow tines

Turf hold down fingers
Rear roller

Hollow tines

Turf hold down fingers
Rear roller

Содержание Verti-Drain 1513



























Результаты поиска

Содержание Verti-Drain 1513

Отзывы:

Бренды по названию

Популярные бренды

Redexim Verti-Drain 1513, Руководство пользователя и каталог запчастей

Результаты поиска

Содержание Verti-Drain 1513

Отзывы:

Бренды по названию

Популярные бренды