Redexim Verti-Drain 1513 Скачать руководство пользователя страница 19

Страница: 19 / 26

13.0 MAINTENANCE

Time line

Check point /

Lubrication point

Method

Before

every

use

Check for loose bolts / nuts.

Tighten the loose bolts/nuts
with the correct torque.

Couple the machine to a tractor
and let the machine run for 5
minutes.

Look and listen for strange
movements/noises.

Check the oil level in the gear
casings.

If necessary, use
80W90 - 0.9 LITER.

Presence and legibility of the
safety stickers.

(Fig.7)

Replace these if
absent/damaged.

Loose parts near the PTO.

Secure the parts so they do
not come close to the PTO.

After

initial

20 operating

hours

Lubricate PTO, roller bearings

Use EP 2 lubricating grease.

(new or repaired)

Check for loose bolts / nuts.

Tighten the loose bolts/nuts
with the correct torque.

Couple the machine to a tractor
and let the machine run for 5
minutes.

Look and listen for strange
movements/noises.

Check the oil level in the gear
casings; this has to reach to the
middle of the level indicator.

Use 80W90 - 0.9 LITER.

Check the gearbox for oil
leakage.

Replace seals / sealant
paste.

Loose parts near the PTO.

Secure the parts so they do
not come close to the PTO.

After

initial

50 operating

hours

(new or repaired)

Change the oil in the gear
casing.

Use 80W90 - 0.9 LITER.

After

every

50 operating

hours

Lubricate PTO, roller bearings

Use EP 2 lubricating grease.

Check for loose bolts / nuts.

Tighten the loose bolts/nuts
with the correct moment.

Couple the machine to a tractor
and let the machine run for 5
minutes.

Look and listen for strange
movements/noises.

Check the gearbox for oil
leakage.

Replace seals / sealant
paste.

After

every

500 operating

hours

Change the oil in the gear
casing.

Use 80W90 - 0.9 LITER.

Содержание Verti-Drain 1513



























Результаты поиска

Содержание Verti-Drain 1513

Отзывы:

Бренды по названию

Популярные бренды

Redexim Verti-Drain 1513, Руководство пользователя и каталог запчастей

Результаты поиска

Содержание Verti-Drain 1513

Отзывы:

Бренды по названию

Популярные бренды