RECO EasyLine RM-216 CB.10 Скачать руководство пользователя страница 12

Страница: 12 / 15

RM-216 CB.10 Easy Line Documentation

RDN 10000088

07.07.2016

8 Text messages on the display

Display

Explanation

Reset status and text version
The text message is displayed for approx. 1 second after the voltage is

switched on.

Reset RM204VXX

Controller is not enabled through inputs I1 and I2.

Stand By

+ - Val.No

The control has been enabled via input E1, E2 and stopped via input D1,

D2.

Cleaning Off

+ - Val.No

The control has been enabled via input E1, E2 and started via input D1,

D2.

Cleaning On

+ - Val.No

Down time cleaning active

DTC Cleaning ON

+ - 000 Pcs

The alarm switching point for the service hours counter has been

exceeded.

Call Service

+ - Val.No

A connected O module RM-LV8 or RM-LV16 is out of order.
or
the total number of valves (parameter P04) is set incorrectly.

RM-LVX Alarm

+ - Val.No

Содержание EasyLine RM-216 CB.10
















Результаты поиска

Содержание EasyLine RM-216 CB.10

Отзывы:

Похожие инструкции для EasyLine RM-216 CB.10

Бренды по названию

Популярные бренды

RECO EasyLine RM-216 CB.10, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание EasyLine RM-216 CB.10

Отзывы:

Похожие инструкции для EasyLine RM-216 CB.10

Бренды по названию

Популярные бренды