background image

TonerRefillKits.com 

 

RechargX™ RX022

Mon - Fri  8am - 5pm ET                     © 1995-2011 ReChargX™, EmptyX, TonerRefillKits and TonerRefillKits.com, the TonerRefillKits logo, the  

2011.05.20

800.527.3712 or 352.343.7533                 ReChargX™ and EmptyX logos are trademarks owned by TonerRefillkits, LLC. All rights reserved. 

Page 2 of 7

Step 3: Plug in the Hole-Making Tool

Plug in the hole-making tool included with the 

ReChargX™ Tool Kit. 

Wait the full 3 minutes (as indicated using the 

sand timer).  Allowing the tool to heat up for 3 

minutes  will  ensure  the  tool  is  hot  enough  to 

penetrate the cartridge more easily (figure 4).

Step 4: Creating the Toner Hopper Hole

Hold the ReChargX hole-making tool directly over 

the location for the hole and press the copper 

hole-making bit against the cartridge allowing 

the heat of the tool to create the toner hopper 

hole.

Let the tool do the work with a minimal amount 

of pressure, as shown in figure 5.

Note:

 Once the copper tip of the hole-making 

tool  slowly  penetrates  the  top  of  the  toner 

cartridge,  immediately  withdraw  the  tool  and 

unplug it from the wall.

Step 5: Remove the Excess Plastic From 

the Hole-Making Tool

Using  the  tip  of  the  flat-blade  screwdriver, 

included in the ReChargX™ Tool Kit, remove 

the small piece of plastic from the copper tip 

of the hole-making tool, as shown in figure 6.

This small piece of plastic becomes impossible 

to remove once it becomes cold and hardens to 

the copper tip of the hole-making tool.

Figure 4

: Wait for the hole-making tool to heat up

Figure 5

: Create the toner hopper hole

Figure 6

: Remove the excess plastic piece

Содержание RX022








Отзывы: