Rebel TOOLS RB-1021, Руководство пользователя

Страница: 19 / 81

6. Use power tools only with specifically designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
7. When battery pack is not in use, keep it away from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal objects, that can make a connection from
one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
8. Under abusive conditions, liquid may be ejected from the battery. Avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally
seek medical help.
Liquid ejected from the battery may cause irritation or burns.
9. Do not use damaged or modified batteries. Damaged or modified batteries may
behave in an unpredictable manner, resulting in hazardous effects (ignition, explosion,
personal injuries).
10. Ensure that the switch is in the OFF position before inserting the battery. Inserting
the battery into power tools with the switch on invites trouble. Injury hazard.
11. Charge battery pack only at ambient temperatures b10°C and +40°C. Store the
battery in a dry location protected from cold where temperature would not 40°C.
Charger use and care
1. Do not attempt to open or disassemble the charger. If the charger has been dropped
or is damaged in any way, stop using it and do not attempt to repair it. Return the
charger for repair to an authorized service center or a qualified person, to avoid any
danger to the user; or discard it according to local laws.
2. Protect the charger against any heat source (e.g. direct sunlight exposure, fire,
heater) to prevent any damage to the charger.
3. Do not expose the charger to water, moisture and cold. Risk of electric shock.
4. If the power cord or the plug becomes damaged, stop suing the charger until it has
been repaired by a qualified person. If the supply cord is damaged, it must be
replaced by the manufacturer or its authorized service center, in order to avoid a
hazard.
Risk of electric shock.
5. Only use the charger provided, or a same type or same model charger to charge the
battery. The use of other types of charger increases the risk of electric shock, personal
injury and damage.
6. Never attempt to recharge non-rechargeable batteries. Explosion hazard.
7. Only use the charger at ambient temperatures b10°C and +40°C. Store charger
in a dry location protected from cold where temperature would not 40°C.
8. The charger is intended for indoor use only. Place charger on solid, flat nonflammable
surface and away from any flammable materials when re-charging the battery pack.
9. Do not recharge the battery pack in a wet or humid environment. The charger and
battery pack may heat during charging process.
Additional safety warnings for angle grinders
• Use appropriate detectors to determine if utility lines are hidden in the work area or
call the local utility company for assistance. Contact with electric lines can lead to
fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a
water line causes property damage or electric shock.
• Use only wheel types and wheel guards that are recommended for the power tool.
Wheels not intended for a particular power tool cannot be protected enough and
therefore are not safe.
• Do not use accessories which are not specifically designed and recommended by the
power tool’s manufacturer. Use of any other accessories pose a hazard of serious
injury and damage to the power tool. It is not because an accessory can be attached to
your tool; that it can assure safe operation. The accessories must meet specific
requirements:
• The rated speed of the accessory must be at least equal to the maximum speed
marked on the power tool.
Accessories operated faster than their rated speed
can break and fly apart.
• Diameter and thickness of the wheel must be appropriate for the power tool.
Incorrectly sized accessories cannot be adequately guarded or controlled.
• Mounting of the wheels, flanges or other accessories must match the spindle
thread of the angle grinder.
Accessories that do not match the mounting
hardware of the power tool are likely to run out of balance; vibrate and are likely
to cause loss of control.
• Do not cut workpiece with diameter greater than the maximum cut depth of the
cut-off wheel.
• Keep the power cord away from the spinning wheel. If you loose control, the power
cord may be cut or snagged and your hand or arm may be pulled into the spinning
wheel.
• Inspect workpiece for any nails and remove them before operation.
• Check for proper clearance beyond he workpiece before cutting
so that the wheel will
not strike the floor, workbench etc.
• Hold the power tool with a firm grip with both hands (if possible) and keep a good
balance . The power tool is best guided with both hands. A strong torque reaction may
occur if a wheel gets locked.
• Secure the workpiece. Never hold the workpiece in your hand or across your legs or
against your body . A workpiece clamped with clamping devices or in a vice is held
more secure than by hand. An unstable workpiece can cause loss of control of the tool
and/or injury.
• Keep hands away from the working range. Do not reach under the workpiece.
Contact with the wheel can lead to injuries.
• Apply the power tool to the workpiece only when switched on . Otherwise there is
danger of kickback when the wheel jams in the workpiece.
• Do not apply too much pressure on the power tool.
• Do not apply side pressure on the wheel.
• Avoid areas in front and behind the spinning wheel.
When a cut-off wheel is moved
onto a workpiece away from the operator, it may cause the power tool to kick back as
a result of recoil, with a rotating cutoff wheel pointing directly towards the operator.
36 37 EN EN