S1M-ZP33-110
S1M-ZP33-110
Safety Warnings Common for rebating
22. Operations such as grinding, sanding, wire brushing,
polishing or cutting-off are not recommended to be
performed with this power tool. Operations for which
the power tool was not designed may create a hazard
and cause personal injury.
23. Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
24. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
25. The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
26. The arbour size of wheels, flanges backing pads or
any other accessory must properly fit the spindle of
the power tool. Accessories with arbour holes that do
not match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause
loss of control.
27. Do not use a damaged accessory. Before each use.
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for ‘cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself
and bystanders away from the plane of the rotating
accessory and run the power tool at maximum no-
load speed for one minute.Damaged accessories will
normally break apart during this test time.
28. Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments. The
eye protection must be capable of stopping flying
debris generated by various operations. The dust mask
or respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
29. Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of workpiece
or of a broken accessory may flyaway and cause injury
beyond immediate area of operation.
30. Hold power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a ‘live’ wire may make
exposed metal parts of the power tool ‘Iive’ and shock
the operator.
31. Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
32. Never lay the power tool down until the accessory
has come to a complete stop. The spinning accessory
may grab the surface and pull the power tool out of
your control.
33. Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
34. Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
35. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
36. Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
37. Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up. The operator can control torque
reactions or kickback forces, if proper precautions are
taken.
38. Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
39. Do not position your body in the area where power
tool will move if kickback occurs. Kickback will propel
the tool in direction opposite to the wheel’s movement
at the point of snagging.
40. Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control
or kickback.
41. Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent
kickback and loss of control.
4
Power switch
Grip handle
Guide plate
Exhaust cover
Accessories
CAUTION: These accessories or attachments are
recommended for use with your RebateMate™ tool
specified in this manual. The use of any other accessories
or attachments might present a risk of injury to persons.
Only use accessory or attachment for its stated purpose.
• Exhaust cover for diamond cutting wheel
• Diamond cutting wheels
• Inner flange
• Lock nut For depressed center wheel
• Lock nut wrench
• Grip handle
• Allen key
• Plastic finishing tool
• Adhesive glue (sold seperately)
INTENDED USE
The tool is intended for rebating of plaster board / villa
board / hardie board / cement sheeting.
RebateMate™ is a specialised head attachment that
eliminates butt joint problems such as weakness, glancing
light issues, cracking, visible joins and plaster wastage in
the join area.
It is designed to cut rebate edges, in preparation for a rebate
or (butt joint), resulting in a stronger seamless joint between
the plaster sheets, in both ceiling and wall application.
This easy to use multipurpose tool is suitable for
plasterboard, Villaboard, Hardie board and cement sheeting.
The RebateMate™ is fitted to a symmetrical cutting wheel,
which can be attached to most commercial vacuum systems
creating a dust free environment.
Creating a rebate with rebatemate™
CAUTION: It should never be necessary to force the
tool. The weight of the tool applies adequate pressure.
Forcing and excessive pressure could result in damaging
the tool and/or the rebated material.
• ALWAYS replace wheel if tool is dropped
• NEVER use tool with any other cutting blades or saw
blades other than the specific diamond blade designed
for RebateMate™. Such blades when used will cause
poor results and may cause loss of control leading to
personal injury.
• ALWAYS hold the tool with two hands to create rebate
5
