Real Flame Vivente VVT100 Скачать руководство пользователя страница 2

2

CAUTION: Please read this information guide carefully to be able to safely install, 
use and maintain your product.

Important Safety Advice

When using electrical appliances, basic precautions should always be followed to reduce 
the risk of fire, electrical shock and injury to persons, including the following:

If the appliance is damaged, check with the supplier before installation and operation.

•  Do not use outdoors.
•  Do not use in the immediate surroundings of a bath, shower or swimming pool.
•  Do not locate the appliance immediately below a fixed socket outlet or connection box.
•  Do not use this heater if it has been dropped.
•  Do not use if there are visible signs of damage to the heater.
•  Use this heater on a horizontal and stable surface.

The appliance is not intended for use by persons (including children) with reduced physical, 
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given 
supervision or instruction concerning use of the appliance by a person responsible for their safety. 
Children should be supervised to ensure that they do not play with the appliance. Children shall 
not plug in, regulate and clean the appliance or perform user maintenance.

CAUTION: 

Some parts of this product can become very hot and cause burns. Particular attention 

has to be given where children and vulnerable people are present.

Do not use this appliance in series with a thermal control, a program controller, a timer or any 

other device that switches on the heat automatically, since a fire risk exists when the heater is 

accidentally covered or displaced.

Ensure that furniture, curtains or other combustible material are positioned no closer than 1 meter 

from the appliance.

In the event of a fault disconnect the appliance.

Disconnect the appliance when not required for long periods.

The appliance must be positioned so that the plug is accessible. Electrical Requirements section 

for more details. If the supply cord is damaged it must be replaced by the manufacturer or service 

agent or a similarly qualified person in order to avoid a hazard.

Keep the supply cord away from the front of the appliance.

Warning: 

This appliance must be earthed.

The use of an extension lead or multi-plug adaptor is not advised when connecting this product 
to the mains. Connection through these devices could lead to a risk of overloading, overheating 
and even fire at the extension lead or adaptor due to inadequate connection quality.
This heater must be used on an alternating current supply (~) only and the voltage marked on 
the heater must correspond to the supply voltage.

Содержание Vivente VVT100


























Отзывы: