Real Flame OPTIMYST CAS1000, Инструкция по установке и эксплуатации

Страница: 4 / 16

3
Operating the Product
ow through the valve. You can shut off the water to the product by turning the tap on the valve clockwise until the
ow stops.
4. Turn on the internal ball valve. This is located under the sump. Remove the sump as described under ‘Cleaning’ in
the Maintenance section
Please note: the water pressure is to be between 0.5Bar (50Kilopascals) and 8Bar (800Kilopascals)
If you do not feel con dent making this connection please consult a quali ed plumber, to ensure a safe and
secure installation.
Electrical Connection
Plug the re into a 10amp/240 volt outlet. Be sure to have access to the plug after installation to allow for disconnection.
Ensure that the supply cable exits at the back of the re, at the right or left hand corner to suit your supply socket location
and is not trapped under the re such that it might cause it to be damaged. If connecting multiple appliances into the
same outlet be sure not to connect more that 5 appliances. If more appliances are required they must be connected into
a separate circuit.
The appliance can be connected to the xed wiring of the premises through a suitable connection box positioned
adjacent to the appliance. This electrical installation must be carried out by a competent electrician and be in strict
accordance with the current regulations for Electrical Equipment in Buildings.
The electrician can remove the supplied plug by the following;
1. Lift off the fuelbed and put switch ‘A’ into the off position (Fig 9).
2. Ensure that the appliance is unplugged.
3. Lift off the access cover by removing the retaining screw (Fig 15).
4. Unscrew and remove the Live, Neutral and Earth wires.
5. Unscrew the cable clamp (Fig 16 ‘A’) and remove the supply cord.
The electrician can then connect their wire from the appliance (by following the steps above in reverse) to the connection
box ensuring that it incorporates a double pole isolating switch having a contact separation of at least 3mm. Brown - Live
(L), Blue - Neutral (N) and Green/Yellow - Earth (E).
Assembling the LED Log Fuelbed
This product is equipped with a ‘metal fuelbed’. Before assembling the LED Log Fuelbed you have to lift off this metal
fuelbed and place aside, (Fig.2). You can keep this for future use. Gently lift the LED Log Fuelbed out of its packaging.
CAUTION: The fuelbed weighs 5kg. Be sure to only lift the Fuelbed by the two center logs (Fig.5). These are
the strongest. Place the Fuelbed on top of the appliance, there are 4 plastic guides under the Fuelbed to help locate
it, (Fig.6). The Fuelbed can be placed front to back or back to front, it is the customers preference how this is to be
orientated. Once in place lift off the small loose log, this is held in place by magnets. Under this log there is a DC wire
jack and a hole through the fuelbed. Connect this to the corresponding DC wire jack on the product through the holes in
the Fuelbed, (Fig.7). The product is now assembled and is ready to be switched on.
There is also a loose non LED log packed with the Fuelbed. For the CAS500 this can be placed on top of the Fuelbed
or stored away with the packaging. For the CAS1000 the loose log can be placed on the center join between the two
Fuelbeds.
Connecting the Receiver
Take your Receiver, 4button for CAS500 and 6button for CAS1000, and with the Fuelbed removed insert the 3.5mm
jack into the socket at the back of the appliance (Fig.8). It is very important to make this connection for the product
to function correctly. The Receiver has a cable length of 1.4m which will allow you position it anywhere around the
product. If you prefer to hide it the Receiver can be placed inside the surround/wall. Please ensure that the Receiver is
not enclosed in metal, concrete or any other dense material, this will affect the signal from the remote control.
This section describes how to activate your re using either the manual controls or remote control.
MANUAL CONTROLS
The manual controls are located beneath the Fuelbed. (Fig.9)
CAS500
Mains Switch ‘A’:- Controls the electricity supply to the appliance.
Note: This switch must be in the ‘ON’ (
I
) position for the appliance to operate
Button panel ‘A’:- Controls the functioning of the appliance
• is the on/standby button. Press it to turn on and off the ame effect. Turning it on will be indicated by the main
lights activating. Be careful not to look directly into the LED’s. These are very bright. Although the main lights operate
immediately it will take a further 45 seconds before the ame effect starts.
• is the Pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’ for details
• is the test mode button. This will be used by the manufacturer and the Service Engineer