manualshive.com logo in svg

Real Flame EXURO IO1000, Инструкция по установке и эксплуатации

Поделиться
Скачать
Real Flame EXURO IO1000 Скачать руководство пользователя страница 19

19

INSTALLATION 

(continued)

Checking Operating Pressure

NOTE: Check ensure that the correct jets, for the gas being used, are installed
– see page 25.

This check is done at the regulator located at the lower front of the appliance.

This must be done before fascia has been fitted.

Pressure test point available for operating pressure (as shown below).

The operating pressure has been factory set. Please check that the operating pressure is exactly
as listed below and if not, adjust the regulator until the pressure is correct. If unable to achieve
this, reassess the inlet gas pressure / pipes.

Replace operating test point screw and leak-test the test point.

Test for overall soundness using an appropriate method.

A = Inlet gas connection

B = Pressure adjustment screw

C = Operating pressure test point

Propane

Natural Gas

ULPG

Minimum Inlet pressure

2.5 kPa

1.0 kPa

2.5 kPa

Maximum Inlet pressure

5.0 kPa

5.0 kPa

5.0 kPa

Operating Pressure

2.0 kPa

1.0 kPa

2.2 kPa

A

B

C

Pressure Table

Содержание EXURO IO1000





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды