RCS TBZ48 Скачать руководство пользователя страница 23

 

FCC/IC 

 

INFORMATION TO USER

 

 

This device complies with Part 15 of the FCC Rules.  Operation is subject to the following 

two conditions:  (1) This device may not cause harmful interference, and (2) This device 

must accept any interference received, including interference that may cause undesired 

operation. 

 

This equipment has been tested and found to comply with the limits for Class B Digital 

Device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide 

reasonable protection against harmful interference in a residential installation.  This 

equipment generates and can radiate radio frequency energy and, if not installed and used 

in accordance with the instructions, may cause harmful interference to radio 

communications.  However, there is  no guarantee that interference will not occur in a 

particular installation.  If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user 

is encouraged to try to correct the interference by one or more of the following measures. 

 

 

Reorient or relocate the receiving antenna 

 

Increase the separation between the equipment and receiver 

 

Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected 

 

Consult the dealer or an experienced radio/TV technician for help 

 

Any changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. 

 

 

This device complies with Industry Canada license-exempt RSS standard(s). Operation is 

subject to the following two conditions: (1) this device may not cause interference, and (2) 

this device must accept any interference, including interference that may cause undesired 

operation of the device. 

 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils 

radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) 

l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter 

tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en 

compromettre le fonctionnement.

 

DCN: 140-02121-06 

Page 23 

 

Содержание TBZ48
























Отзывы: