o
ds,
k
).
e
th
s
T
t
e
4-way conference call (Line 1 + Line 2 + 2 extension):
1. Once the base unit or handset has both Line 1 and 2 on hold, press the
intercom
button and then select the desired handset or base to intercom.
2. The selected handset or base will emit a page tone. The user can press the
Talk
button on the handset or the speaker button on the base to answer
the intercom call page.
3. The originating caller can then press the
CONF
Soft key shown on the
display to initiate a conference. Since Line 1 and 2 are both on hold, the
user will be prompted to select Line 1, Line 2 or Both to conference with.
The user can then use the Soft keys to select the desired option. If the
BOTH
Soft key is selected a 4-way conference is established between the
originating caller, both lines and the intercom call.
Note: After the base jointed the call, you can press base HEADSET button/
conference.
Hold
In headset talk mode, press the hold button on the base unit or press and
hold
button on the headset for 3 seconds. Line
X ON HOLD
shows
When the line is on hold, the hold alert tone will be emitted to both the
person on hold and to the user that initiated the hold.
Press the corresponding
LINE
Soft key on base to release the hold and pick
up the call again.
Intercom Operation
Join an Intercom
While the base unit is on an intercom call with a cordless handset, you can
press the Headset button on the base unit or
button in headset to
transfer the active intercom call to the headset.
button on the headset or the Headset
button on the base unit again or place the headset in the cradle.
Note: The maximum total number of wireless devices that can be paired
with a single base station is 10. Since the headset functions as one of these
10 devices, only 9 handsets can be registered along with the headset.
Answering an Intercom Call on the headset
base unit.
button on the base unit, or place the headset in the cradle.
Auto Standby
(during a call), the current call will be automatically disconnected.
Accessing and dialing numbers from the Caller ID, Phonebook or
One-Touch/ memory Records
While reviewing CID records, Phonebook memory listings or
One-Touch/Memory Records on the base unit, you can dial the numbers
shown on the display by pressing headset button on the base unit or the Talk
OTHER INFORMATION
Battery Safety Precautions
t
Do not burn, disassemble, mutilate, or puncture. Like other batteries of
this type, toxic materials could be released which can cause injury.
battery listed in this User’s Guide.
t,FFQC
atteries out of the reach of children.
t
Remove battery pack if storing over 30 days.
indicates that we are participating in a program to collect and recycle the
rechargeable battery (or batteries). For more information go to the RBRC web
site at www.rbrc.org or call 1-800-8-BATTERY or contact a local recycling
center
TROUBLESHOOTING GUIDE
Telephone Solutions
No dial tone
t$IFDLBOE
repeat installation steps:
Ensure the base unit power cord is connected to a working outlet.
Ensure the telephone line cord is connected to the base and the wall jack .
t
Connect another phone to the same jack; if there is still no dial tone, the
problem might be your wiring or local service.
t
The cordless handset/headset may be out of range of the base. Move
closer to the base.
t&OTV
re the battery is properly charged (14 hours).
t&OTV
re the battery pack installed correctly.
t%JEUIFIFBETFUCFFQXIFO
you pressed the
button? The
battery may need to be charged.
Unit will not dial out
t
Make sure your phone service supports
TONE
dialing or Pulse dialing,
This unit support the two mode both but the default mode is
"Tone".
Headset does not ring
t
Make sure the headset ringer is set to on.
t
The cordless headset may be out of range. Move closer to the base.
t$IFDL
for dial tone. If no dial tone is heard, see No dial tone above.
You experience static, noise, or fading in and out
t
The cordless headset may be out of range of the base. Move closer to the
base.
t$IB
rge the battery.
Unit beeps
t$MFBODIB
rging contacts on cordless handset and charge cradle with a
soft cloth or an eraser.
t
See solutions for “No dial tone” on previous page.
t
Replace the battery.
Unit locks up and there is no communication between the base unit and
the cordless handset
t6OQMVHUIF
AC power adaptor from the wall outlet and the back of the
base unit, and remove the backup batteries from the bottom of the base
unit (if previously installed). Remove the headset battery. Wait for 30
seconds and plug the power adaptor back into the base unit and wall
outlet, and re-install the batteries in the base unit. Reconnect the headset
battery and charge for 14 hours.
BATTERY SOLUTIONS
If you experience any of the following problems, even after fully recharging
the battery, you may need to replace the battery pack:
t4IP
rt talk time
t
Poor sound quality
t-JNJ
ted range
GENERAL PRODUCT CARE
To keep your unit working and looking good, follow these guidelines:
t
Avoid putting the phone near heating appliances and devices that generate
t%0/
OT expose to direct sunlight or moisture.
t
Avoid dropping the handset, as well as other rough treatment to the phone.
t$MFBOVOJUPOMZXJUIBTP
ft, dry cloth.
t/F
ver use a strong cleaning agent or abrasive powder because this will
t
Retain the original packaging in case you need to ship the phone at a later
date.
t
Periodically clean the charge contacts on the handset and charge cradle
with a clean pencil eraser.
ENVIRONMENTAL CAUSES OF POOR RECEPTION
t
Aluminum siding on the outside of a building.
t
Foil backing on some types of in-wall insulation.
t)F
ating ducts and other metal construction that can shield radio signals.
t
You’re too close to appliances such as microwaves, stoves, computers, etc.
t
Atmospheric conditions, such as strong storms.
t#BTFVOJUJTQMVHHFEJ
nto AC outlet with other electronic devices.
t#B
by monitor is using the same or similar frequency.
t)FBETFUC
attery is low.
t
You’re out of range of the base.
Warranty
Warranty Assistance
If trouble is experienced with this equipment, for warranty information,
please contact customer service at 1-800-511-3180. If the equipment is
causing harm to the telephone network, the telephone company may
require that you disconnect the equipment until the problem is resolved.
For instructions on how to obtain a replacement unit, refer to the warranty
included in this guide or call customer service at 1-800-511-3180.
Or refer inquiries to:
Beaverton, OR 97005
Attach your sales receipt to this booklet for future reference. Also, make
note of your purchase date and where the unit was purchased. This
information may be helpful if service should be required during the warranty
period.
Purchase Date
________________________________________________________________
Name of Store
________________________________________________________________
