background image

similar-sized sealed system. TAV™ technology shifts the vent tuning to a much lower 
frequency than would otherwise be possible in a small vented enclosure and also 
improves transient response. The MS-10.1 features the TAV™ Technology.

The subwoofer cabinets are constructed from medium density fiberboard because of 
its inert properties. The thickness of the front baffles also prevents excess acous-
tic radiation. Large binding posts ensure a good electrical contact. Sophisticated 
computer modeling and measurement techniques are used extensively in the RBH 
Sound subwoofer design process.

Features

 

(continued)

3

Setup Suggestions 

WARNING! Make certain the proper power cord is being used and the AC voltage 

selector switch is set to either 115V or 230V to match the power voltage in your 

area. Refer to the Amplifier Controls and Setup section of this manual.

In order to obtain the best possible sound from your subwoofer, it is important 

to determine where the subwoofer will sound best in your listening room. Sound 

reflections from the floor, ceiling and side walls influence the balance, imaging and 

overall sonic quality at the listening position. Experiment with subwoofer placement 

to determine which location offers the best overall sound. 

Placement of the subwoofer will largely determine quality, quantity and extension of 

the bass frequencies within your listening room. Bass frequencies are reinforced by 

close room boundaries. Placing the subwoofer in a corner will make the subwoofer 

sound louder and boost the very lowest frequencies.

Placing the subwoofer away from walls will provide the least reinforcement, making 

the bass sound subjectively thinner than if the woofer were closer to a wall. Good 

results can usually be obtained by placing a subwoofer along a wall 1-3 feet from a 

corner. Experiment with placement of the subwoofer and the sub-amplifier controls 

to achieve the proper bass balance. 

IMPORTANT NOTICE REGARDING BASS MANAGEMENT: 

It is important the signal being 

sent to the subwoofer be a non-boosted or “flat” signal. To be sure of this, check the 
settings on your receiver or processor to make sure any “bass boost”, “super bass” 
or  “loudness”  is  set  to  Off.  In  most  cases  for  home  theater,  setting  a  receiver  or 
processor will determine the crossover frequency through bass management settings. 
In this configuration, connect the receiver or processor to the LFE Line Level Input. 
Your subwoofer can now reproduce the bass frequencies the way they were originally 
recorded. Use the subwoofer level control and the individual bass management control 
within the receiver or processor to adjust the subwoofers’ volume if necessary. Once 
set, the volume controls should not need to be altered as the subwoofer’s volume will 
coincide with the master volume control of your receiver or processor.

Содержание subwoofer

















Отзывы: