Raytools BM111 Series Скачать руководство пользователя страница 26

Страница: 26 / 29

V1.0 Shanghai Empower Technologies Co., Ltd. © Copy Right

www.empower.cn

BM111 SERIES 3KW Auto-Focusing Laser Cutting Heads User Manual

25 | 28



Turn the focusing lens back into the focusing lens mount and tighten it.



As the sequence shown in figure 1.1, reassemble and tighten the screws.



Check the focus position is at the center of nozzle or not. If not, you need to refer to the

3.1 step to reset the operation.

6.3

Replace Nozzle Connection Assembly

During the laser cutting, the laser head will inevitably be hit, so users need to replace the

nozzle connector.

6.3.1

Replace Ceramic Structure



Unscrew the nozzle.



Hand pressing the ceramic structure so that it is not skewed, and then unscrew the

pressure sleeve.



Align the pinhole of the new ceramic structure with the 2 locating pins and press the

ceramic structure by hand, then screw the pressure sleeve.



Screw the nozzle and tighten it properly.

Fig 6.7 - Focus lens installation diagram

Spring pressure ring

Focusing lens

Focusing lens mount

Fig 6.8 - Replace nozzle connector

Ceramic structure

Nozzle

Pressing sleeve

Содержание BM111 Series






























Результаты поиска

Содержание BM111 Series

Отзывы:

Похожие инструкции для BM111 Series

Бренды по названию

Популярные бренды

Raytools BM111 Series, Руководство пользователя

Результаты поиска

Содержание BM111 Series

Отзывы:

Похожие инструкции для BM111 Series

Бренды по названию

Популярные бренды