Raytools BM109 SERIES Скачать руководство пользователя | Manualshive

Страница: 20 / 25

background image

V1.0

Shanghai Empower Technologies Co., Ltd. © Copy Right

19 | 24

www.empower.cn

BM109

SERIES 1.5KW Auto-Focusing Laser Cutting Heads

User Manual

screw the spring compression ring appropriately with force, and re-screw it into the collimating

components;



Lock the screws of the collimating components;



Check whether the focus position is in the center of the nozzle hole before use, if it is not in the

center, it is necessary to carry out center-regulating operation again.

5.2.4

Removal and Installation of Focus Lenses



Removal and installation of focus lenses refer to the following steps.



Remove the laser head, move it to a clean place, and clean all dust on the laser head surface;



Place the laser head horizontally. As shown in Figure 6.7, remove the locking screws from bottom

Locking

screw

Figure 6.5 - Disassemble collimation

components

Figure 6.6 - Diagram of installing collimation lens

Elastic pressing ring

collimation lens

collimation lens holder

Figure 6.7 - Lens taking

Protective mirror assembly

Nozzle assembly

M4

inner hexagon screw

M4

inner hexagon screw

Focusing components

Collimating water-cooled components

«
...
18
19
20
21
22
...
»

Содержание BM109 SERIES


























Отзывы:

Нет отзывов

Похожие инструкции для BM109 SERIES

Бренд: P.Lindberg Страницы: 86

Бренд: Ogura Страницы: 16

PLAN 100 Series

Бренд: Rapid-Air Страницы: 58

Бренд: Zipper Mowers Страницы: 13

Бренд: Hwayuan Electric Страницы: 49

Бренд: US Cutter Страницы: 49

Бренд: RASOR Страницы: 15

Бренд: Land Pride Страницы: 70

Бренд: Baileigh Industrial Страницы: 48

Бренд: Tanaka Страницы: 6

Hurricane MaX F-580BiS

Бренд: Vari Страницы: 64

PowerPlus GardenPro POWXG3041

Бренд: VARO Страницы: 15

Бренд: Garland Страницы: 144

Бренд: RASOR Страницы: 12

Бренд: Far Tools Страницы: 42

Бренд: Far Tools Страницы: 74

Бренд: Brother Страницы: 2

Бренд: Brother Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды