Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 147

Страница: 147 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

131

10000001052

5.2 Operation elements of the Additional Autopilot Control Unit

Table 34

Operation elements AACU

No. Section

Description

Date and Time

Information

The section Date and Time Information displays the
Date, UTC and local time.

2 Navigation

The section NAVIGATION displays the related
navigational sensor information.

3 Autopilot Values

The section AUTOPILOT VALUES displays the current
values set on the NautoPilot®.

Opens the menu for general settings.

5 Panel

The section PANEL displays the current mode of the
panel. In addition, the settings can be changed via touch
operation.

6 Control

The section CONTROL activates the Additional
Autopilot control and the ruder limit can be adjusted.

5.2.1

Date and Time Information

This section displays the Date and Time Information.

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды