Raytec VAR2 IPPOE i4-1 Скачать руководство пользователя страница 7

Страница: 7 / 64

Colour

Description

Wire Gauge (AWG)

Orange

External Input -Volt free or TTL +ve

Purple

External Input -Volt free or TTL GND

Yellow

External Output – Volt free

White

External Output - Volt free

WARNING

To maintain the IP rating of the product the multi-core auxiliary cable

must be waterproofed and terminated appropriately even if it is not in use.

PoE Detection – Resistance Selection Switch

There is a switch on the

VAR2-IPPoE-w8-1, i8-1

and

i8-1-C

illuminators which can

be used to change the PoE detection resistance of the illuminator (24.9K

Ω

is the

factory default setting).

Turn the power to the illuminator OFF, remove the baseplate and access the switch as

shown.

The majority of PSE equipment requires a detection resistance of 24.9K

Ω

to establish

a PoE link. Some models of PSE equipment require a 12.5K

Ω

detection resistance.

Check with your supplier of PSE equipment.

For 24.9 K

Ω

, slide switch to the LEFT (factory default – as shown). For 12.5 K

Ω

, slide

switch to the RIGHT.

Detection Resistance Selection Switch

Содержание VAR2 IPPOE i4-1

































































Результаты поиска

Содержание VAR2 IPPOE i4-1

Отзывы:

Raytec VAR2 IPPOE i4-1, Полное руководство по установке и настройке, Страница: 7 / 64

Результаты поиска

Содержание VAR2 IPPOE i4-1

Отзывы: