Raypak TempTracker mod+ Hybrid Скачать руководство пользователя страница 32

Страница: 32 / 56

Raypak, Inc.

HTC# 059105-00D

• If required:

Adjust the Water Offset in mild weather

. If the ambient building

temperatures are too warm in mild weather, decrease the offset. If the ambient building

temperatures are too cold in mild weather, increase the Water Offset.

• The rule of thumb for baseboard radiation is to change the offset 4°F for every 1°F you wish

to change the building temperature. In radiant heat applications, change the offset 1F° or

2F° for every 1F° you wish to change the building temperature.

outdoor cutoff temperature

Adjustable: Off, from 20

F / 70

C - 100

F / 38

C, On

Default: 65ºF/ 18

Button:

MENU/System Target/Offset/Outdoor Cutoff

• The control will turn heating off if the outside temperature rises above the Outdoor Cutoff.

This setting shall not affect any indirect DHW requirement.

• The Outdoor Cutoff screen will automatically appear after setting the Offset.

• When the outdoor temperature falls to the adjustable Outdoor Cutoff temperature, the

TempTracker mod+ Hybrid will operate the boilers to hold the calculated temperature.

Outdoor Temperature (in °F)

70 60 50 40

-10

-20

120

140

130

150

160

170

180

100

110

ater

Temperature (in °F)

Custom Reset Ratio

Point1: System=120°F

Oudoor=60°F

Point2: System=170°F

Oudoor=0°F

Point1

Point2

Customized Reset Ratio

Max Target

Min Target

Outdoor Temperature (in °F)

70 60 50 40

-10

-20

120

140

130

150

160

170

180

100

110

ater

Temperature (in °F)

Target Offset

Offset=10°F

Reset Ratio=1.5 : 1.0

Reset Ratio

Max Target

Min Target

Reset Ratio + 10F Offset

Min Target=120°F

Max Target=170°F

• When the outdoor temperature rises to the Outdoor Cutoff plus a 2°F differential, the

TempTracker mod+ Hybrid will turn all boilers off. The System relay will remain energized

for the Run-On delay then de-energize.

• The Outdoor Cutoff can be set from 20°F to 100°F. In addition, it can be set to ON or

OFF. In the ON position, the System Relay will run regardless of the Outdoor temperature

(OD) and the burner stages will be active to hold the calculated water temperature. (Note:

The lowest water temperature the TempTracker mod+ Hybrid will circulate is 70°F. If the

Outdoor Cutoff is turned ON and the Season is set to Winter, the TempTracker mod+ Hybrid

will circulate at least 70°F water even in the hottest of weather.) In the OFF position, the

system pump will always be off and all burner stages will be off.

- OUTDOOR CUTOFF -

[

]

BACK

▲

▼

SAVE

Minimum Water temp

Adjustable from 50

F/10

C to 180

F/82

Hybrid Default: 70

F/ 21

Staging or Modulation Default: 120

F/ 49

Button:

MENU/System Target/Offset/Outdoor Cutoff/Minimum Water Temp

• The Minimum Water Temperature must be set to the boiler manufacturer’s specification.

The TempTracker mod+ Hybrid will calculate the Set Point based on the Outdoor

temperature (OD), the Reset Ratio, and the Offset value. The TempTracker mod+ Hybrid

will control all boilers to hold either the Set Point temperature, or the Minimum Water

Temperature, whichever is higher.

• The Minimum Water Temperature must be at least 20°F lower than the Maximum

Temperature (See next setting).

MINIMUM WATER TEMP

[ ]

BACK

▲

▼

SAVE

Maximum Water temp

Adjustable 70

F/21

C - 220

F/104

Default: 200

F/93

Button:

MENU/System Target/Offset/..../Maximum Water Temperature

• This is the highest temperature heating water the TempTracker mod+ Hybrid will circulate

through the heating system.

• When using a radiation system, it should be set according to the tubing or floor

manufacturer’s specification.

• The Maximum Temperature must be at least 20°F higher than the Minimum Temperature

(See previous setting).

MAXIMUM WATER TEMP

200

[

]

BACK

▲

▼

SAVE

Содержание TempTracker mod+ Hybrid

























































Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды

Raypak TempTracker mod+ Hybrid, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TempTracker mod+ Hybrid

Отзывы:

Бренды по названию

Популярные бренды