manualshive.com logo in svg

Raypak Professional PS10353ti-E-HC, Инструкция по установке и эксплуатации, Страница: 10 / 24

Поделиться
Скачать
Raypak Professional PS10353ti-E-HC Скачать руководство пользователя страница 10

10

Controls 

Your heat pump pool heater incorporates digital safety
controls  and  indicators  to  ensure  its  safe,  reliable
operation.

Water Pressure Switch:

Prevents operation when the

pump is OFF. The unit requires 5 psi minimum pres-
sure.

Digital Water Temperature Control:

The pool water

temperature  is  controlled  by  the  heat  pump  pool
heater’s  digital  control  system,  which  gives  you  the
option of two settings: one for the desired spa temper-
ature and the other for the desired pool temperature.
Additionally, as mentioned earlier, the unit is compati-
ble  with  most  ‘2-wire’  and  ‘3-wire’  control/automation
systems.

Defrost Sensor:

Prevents unit operation if ambient air

temperature  falls  below  a  predetermined  safe  mini-
mum (approximately 42°–48°F (5.5

°

-8.8

°

C) based on

humidity). The  compressor  will  shut  OFF  but  the  fan
will continue to run.

Delay Timer:

Prevents compressor from short cycling,

which  could  damage  or  destroy  the  hermetic
motor/compressor.  Upon  water  temperature  control
satisfaction,  or  other  circuit  interruptions,  this  solid
state  device  will  prevent  compressor  restart  for
approximately 5 minutes.

Operating Instructions

The electronic board has the capability of memorizing
two different programmed temperature settings as fol-
lows (refer to Fig. 5):

• 

For a pool, maximum 95°F (35°C)

• 

For a spa, maximum 104°F (40°C)

To Select Pool or Spa Mode

To have access to either one of these programs, press
the 

SET

key until you see 

P _S

and by pressing the

UP or DOWN key you can switch to 

POL

or 

SPA

.

To Increase the Desired Water

Temperature (Pool or Spa Mode)

Push the 

SET

key until you see 

POL

or 

SPA

. The pro-

grammed temperature will be displayed. Press the UP
arrow to increase the temperature setting one degree
at a time.

To Lower the Desired Water

Temperature (Pool or Spa Mode)

Push the 

SET

key until you see 

POL

or 

SPA

. The pro-

grammed  temperature  will  be  displayed.  Press  the
DOWN arrow to decrease the temperature setting one
degree at a time.

Once the control has been programmed to the desired
pool water temperature, the programmed temperature
will  be  displayed  for  approximately  5  seconds.  Then
the  digital  display  will  display  the  actual  pool  water
temperature.

To  make  the  Board  a  Pool  ONLY  Board,  call  800-
260-2758 for instructions.

To Select Temperature in °C or °F

Press the 

SET

key until you see 

F _C

. By pressing the

UP or DOWN key you can switch to 

°F

or 

°C

. Once the

temperature  display  mode  has  been  programmed  it
will  be  displayed  for  approximately  5  seconds,  then
the  digital  display  will  return  to  the  actual  pool  water
temperature in the mode that you have chosen.

Fig. 5: Digital Water Temperature Control

WARNING:

Install a check valve and/or a Hartford

loop  AFTER  the  heat  pump  pool  heater  and
BEFORE any chlorinating devices. Install any auto-
matic chemical feeders AFTER the heat pump pool
heater.

Improper installation of any type of auto-

matic  chemical  feeders  can  result  in  serious
damage  to,  or  premature  failure  of,  the  heat
pump  pool  heater  and  will  void  the  heat  pump
pool heater warranty.

Содержание Professional PS10353ti-E-HC

























Отзывы:

Нет отзывов