manualshive.com logo in svg

Raypak 503-2003, Инструкция по установке и эксплуатации

Поделиться
Скачать
Raypak 503-2003 Скачать руководство пользователя страница 4

 

2 

PAY ATTENTION TO THESE TERMS: 

 

DANGER: 

 

Indicates the presence of immediate hazards which will cause severe personal injury, 
death or substantial property damage if ignored. 

 

WARNING: 

 

Indicates the presence of hazards or unsafe practices which could cause severe personal 
injury, death or substantial property damage if ignored. 

 

CAUTION: 

 

Indicates the presence of hazards or unsafe practices which could cause minor personal 
injury or product or property damage if ignored. 

 

NOTICE: 

 

Indicates special instructions on installation, operation, or maintenance which are impor-
tant but not related to personal injury hazards. 

 
 

 

DANGER:

 Make sure the gas on which the 

heater will operate is the same type as that 
specified on the heater rating plate. 

 

 

WARNING:

 Should overheating occur or the 

gas supply valve fail to shut, do not turn off or 
disconnect the electrical supply to the heater. 
Instead, shut off the gas supply at a location 
external to the heater. 

 

 

WARNING:

 Do not use this heater if any part 

has been under water. Immediately call a 
qualified service technician to inspect the 
heater and to replace any part of the control 
system and any gas control which has been 
under water. 

 

 

WARNING:

 To minimize the possibility of 

improper operation, serious personal injury, 
fire, or damage to the heater: 

•

 

Always keep the area around the heater 
free of combustible materials, gasoline, 
and other flammable liquids and vapors. 

•

 

Heater should never be covered or have 
any blockage to the flow of fresh air to the 
heater. 

 

 

WARNING: 

Risk of electrical shock. More 

than one disconnect switch may be required to 
de-energize the equipment before servicing. 

WARNING - CALIFORNIA PROPOSI-
TION 65:

 This product contains chemicals 

known to the State of California to cause can-
cer, birth defects or other reproductive harm. 

 

CAUTION:

 Operation of this heater in low-

temperature systems requires special piping. 
Harmful internal condensation will occur if 
the inlet water temperature does not exceed 
105°F. Warranty claims will be denied when 
condensation occurs. 

 

CAUTION:

 If this heater is to be installed 

above radiation level, it must be provided with 
a low water cut-off device at the time of heater 
installation. 

 

CAUTION: 

This heater requires forced water 

circulation when the burner is operating. See 
minimum and maximum flow rates. Severe 
damage will occur if the heater is operated 
without proper water flow circulation. 

 

CAUTION: 

If this heater is to be installed in 

a negative or positive pressure equipment 
room, there are special installation require-
ments. Consult factory for details. 

 
 

WARNINGS

 

Содержание 503-2003



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды