Raypak 503-2003 Скачать руководство пользователя страница 22

Страница: 22 / 58

SECTION C: Installation

CIRCUIT

BREAKER

WHITE

GROUND

BLACK

GREEN

A B

Fig. 17: Wiring Connections

Check the power source:

AC = 108 VAC Minimum, 132 VAC MAX
AB = 108 VAC Minimum, 132 VAC MAX
BC = <1 VAC Maximum

Fig. 18: Multi-meter

Making the Electrical Connections

Refer to Fig. 16-19.

Verify that circuit breaker is properly sized by
referring to heater rating plate. A dedicated circuit
breaker should be provided.

NOTE: Current draw noted on rating plate does
not include pump current.

Turn off all power to the heater. Verify that power
has been turned off by testing with a multi-meter
prior to working with any electrical connections or
components.

Observe proper wire colors while making electri-
cal connections. Many electronic controls are
polarity sensitive. Components damaged by im-

proper electrical installation are not covered by
warranty.

Provide overload protection and a disconnect
means for equipment serviceability as required by
local and state code.

Install heater controls, thermostats, or building
management systems in accordance with the appli-
cable manufacturers’ instructions.

Conduit should not be used as the earth ground.

NOTICE:

A grounding electrode conductor shall be

used to connect the equipment grounding conductors,
the equipment enclosures, and the grounded service
conductor to the grounding electrode.

Field Wiring Connection

CAUTION:

Label all wires prior to disconnection

when servicing controls. Wiring errors can cause im-
proper and dangerous operation. Verify proper
operation after servicing.

DANGER: SHOCK HAZARD

Make sure electrical power to the heater is discon-
nected to avoid potential serious injury or damage to
components.

Fig. 19: Wiring Location

Содержание 503-2003



























































Результаты поиска

Содержание 503-2003

Отзывы:

Бренды по названию

Популярные бренды

Raypak 503-2003, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 503-2003

Отзывы:

Бренды по названию

Популярные бренды