Raynor Premium series 8500RGD Prodigy II Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

Raynor Premium series 8500RGD Prodigy II Скачать руководство пользователя страница 18

18

When in Battery Backup mode, wireless MyQ

®

devices and Timer-To-Close will be disabled.

If the optional Battery Backup is part of this installation it should be installed at this time.
The Battery Backup can be mounted to either the ceiling or a wall within 3 feet (.9 m) of
the garage door opener.

1. Unplug the garage door opener.

2. Position the Battery Backup on a structural support (ceiling joist or wall stud).

3. Attach the Battery Backup to the support with the 1-1/2 inch lag screws (2) provided.

There are mounting holes on either side of the Battery Backup.

4. Connect the Battery Backup cord into the connector on the bottom of the garage door

opener.

5. Follow all instructions included with the Battery Backup to test for proper operation.

Install the Battery Backup (optional)

9

Installation

Battery Backup Cord

475RGD Battery Backup

Connector

«
...
16
17
18
19
20
...
»

Содержание Premium series 8500RGD Prodigy II





































Отзывы:

Нет отзывов