background image

6

Requires B2 wiring type and compatible LiftMaster remote control. 
In C2 wiring the remote control will open the door only.

Press remote control button.

Door should open. Allow the door to fully open.

Press remote control button.

Door should close. Allow door to fully close.

TESTING

Turn on power, LED will fl ash 4 times on power up. Test all controls and entrapment protection devices to make sure they are working 
properly. It may be necessary to refer back to the installation manual for adjustment of the limits.

IMPORTANT NOTES:

•   Do not leave power to the operator on unless all entrapment protection devices have been tested and are working properly.

•   Be sure you have read and understand all safety instructions included in this manual.

•   Be sure the owner or person(s) responsible for operation of the door have read and understand the safety instructions, know how to 

electrically operate the door in a safe manner and how to manually disconnect the door from the operator.

Press OPEN button. (The door should move in the open 
direction.)

Press STOP button. (The door should stop.)

Press CLOSE button. (The door should move in the close 
direction.)

Release CLOSE button. Door should stop if in C2 mode. 
(The door should continue closing if in B2 mode.)

Press STOP button. (The door should stop.)

1

2

3

TEST 3-BUTTON CONTROL STATION

4

5

 Press OPEN button. (The door should open.)

 Allow the door to fully open.

Press CLOSE button. (The door should close.)

Allow the door to fully close.

If the limits are not set properly, remove power and adjust limits 
(refer to installation manual).

1

2

3

TEST LIMIT ADJUSTMENT

4

Open the door.

Place an obstruction in the path of the photoelectric sensors 
or sensing edge.

Press the CLOSE button. The door should not close if 
photoelectric sensors are installed. The door should close to 
obstruction and reverse if sensing edge is installed.

Remove the obstruction.

Press CLOSE button. Door should close. 

If door did not reverse from obstruction, check entrapment 
protection devices.

1

2

3

TEST THE ENTRAPMENT PROTECTION DEVICES

4

5

TEST REMOTE CONTROL

1

2

3

4

To avoid SERIOUS personal INJURY or DEATH:
•   Disconnect electric power BEFORE performing ANY 

adjustments or maintenance.

•   ALL maintenance MUST be performed by a trained door 

systems technician.

ATTENTION 

AVERTISSEMENT 

AVERTISSEMENT 

AVERTISSEMENT 

WARNING 

CAUTION 

WARNING 

WARNING 

WARNING 

PRECAUCIÓN 

ADVERTENCIA 

ADVERTENCIA 

ADVERTENCIA 

Содержание MT5011UCHB













Отзывы: